8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 1/9

68-1

 

Interior mirror

Automatic dimming interior mirror 

The automatic dimming interior mirror darkensinfinitely when the driver is "blinded" frombehind.

It consists of a mirror element with two

electronically controlled photo sensors.

The electronics recognize the light incidencefrom the front and the rear through the photosensors.

If the light incidence is greater from the rear thanfrom the front the electronics apply voltage to the

conductive coating.

The applied voltage changes the color of theelectrolyte. The greater the voltage the darkerthe electrolyte. Therefore the light incidence isreflected to a lesser degree.

When selecting the reverse gear or activiating

the switch in the interior mirror, the dimmingfunction is switched off and one can use themirror to back out of a dark garage.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 2/9

68-2

 

1 - Interior mirror 

Checking function:

- Switch ignition on.

 

- Cover photo sensor - 4 - and shine a flashlight at photosensor - 2 -, the mirror must darken when doing this(reverse gear must not be engaged and automatic anti-dazzle must be activated).

2 - Photo sensor 

3 - Switch 

To manually turn automatic dimmer on and off.

4 - Photo sensor 

5 - Electronics 6 - Glass pane 

7 - Electrolyte coating 

8 - Silver reflective coating 

9 - Conductive coating 

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 3/9

68-3

 

Interior mirror, removing and installing 

Removing

Notes:  

Installing

- Press interior rear-view mirror -1- downward at an angle off retaining plate (spring clip inmirror base).

In cold climates, warm the windshield by running the defroster on high for a few minutes. 

To aid removal, rotate mirror counter clockwise as you pull down.

  - Place mirror -1- in position, turned 60 to 90 from mounted position, and turn indirection of arrow until locking spring clicks into place.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 4/9

68-4

 

Retaining plate for interior mirror,

installing 

Materials:

Glass-metal adhesive kit D 000 703 A1

  Tools:

1 - Glass scraper (commercially available)

2 - Blade (commercially available)

- Remove mounting plate from mirror base.

- Remove PUR adhesive from mounting plate with a wire brush.

- Grind off three spacer protrusions on bonding surface using sandpaper (360/400 grit)on flat surface.

- Keep sanded surface clean and free of grease.

- Scrape PUR adhesive material and primer from windshield down to ceramic layer usingglass scraper.

- Clean bonding area with adhesive remover D 002 000 10 or cleaning solution D 009

401 04.- Allow cleaner to dry at least 10 minutes.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 5/9

68-5

 

CAUTION!  

Do not damage ceramic coating. Scratches will remain permanently visible. 

- Cut nylon mesh fabric exactly to the size of themirror base.

Note:  

Wear hand protection (rubber gloves). 

- Apply adhesive evenly and smoothly to base ofmirror.

- Apply nylon mesh fabric onto base of mirror.

 - Apply further adhesive to nylon mesh fabric by

dabbing with the tube.

30 seconds are available from applying theadhesive to the nylon mesh fabric to pressing it

onto the windscreen.

- Press base of mirror firmly (do not use force)against windscreen for 15 seconds.

- Remove excess adhesive with a cloth.

  Note:  

Interior mirror can be installed after 15 minutes. 

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 6/9

68-6

 

Interior mirror (with rain sensor), removing and

installing 

Removing

Installing

Install in reverse order of removal.

- Press left -1- and right -5- covers apart and remove.

- Pull wiring connectors -3- out from mirror base -4- and separate.

- Pull mirror base -4- with mirror -6- downwards off retaining plate -2- -arrow-.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 7/9

68-7

 

Retaining plate for interior mirror (with

rain sensor), installing 

Removal of windshield is not necessary.

Detatched retaining plates can be cleaned andreused.

Preparing windshield

- Scrape PUR adhesive material and primer fromwindshield down to ceramic layer using glassscraper.

- Clean adhesive surface with cleaning solution D009 401 04.

- Allow cleaner to dry at least 10 minutes.

 - Apply glass/paint primer D 009 200 02.

 - Allow primer to dry minimum 10 minutes to

maximum 1 hour.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 8/9

68-8

 

Preparing detached or new retaining plate

- Remove PUR adhesive from mounting plate withwire brush if reusing plate.

- Prepare adhesive surface by wet-sanding withfine emery paper (800-1200 grit) until waterremains (does not bead and run off) on adhesive

surface.

- Clean with cleaning solution D 009 401 04.

  Bonding mirror base on

- Apply 2K polyurethane adhesive D 180 KD2 A1

direct to prepared and cleaned mirror baseadhesive surface.

- Adhesive bead diameter: Approx. 2.5 to 3 mm(1/8 in.).

- Press mirror base into position on preparedwindshield immediately after applying adhesiveto base.

- Align mirror base in position on ceramic pre-coatsurface and secure using adhesive tape.

8/7/2019 demontare oglinda interioara

http://slidepdf.com/reader/full/demontare-oglinda-interioara 9/9

68-9

 

Cleaning and removing excessive adhesive

- Carefully remove adhesive tape 30 minutes to 1hour after attaching mirror base.

- Carefully remove excess soft adhesive usingspatula.

- Remove remaining excess adhesive completelyusing a cloth or primer applicator soaked incleaning solution.

Installing rain sensor and mirror

- Mirror can be installed after adhesive dries

minimum 2.5 hours.