CODURI AWARD03 Flag resister test06 CPU register test09 System hardware initialization0C BIOS checksum0F DMA page register initialization12 Test DMA address and count registers15 DMA initialization18 Timer test1B Timer initialization1E Start RAM initialization21 Test base 64K of RAM24 Setup init. and temp stack27 Initialize PIC2A Interrupt mask register test2D Hot interrupt test30 V40 DMA if present33 Verify system clock initialization36 Keyboard test39 Setup interrupt table3C Read system configuration switches3F Video test42 Serial port determination45 Parallel port determination48 Game port determination4B Copyright message display4E Calculation of CPU speed54 Test of system memory55 Floppy drive test57 System initialized before boot5A Call to Int 19CODURI PHOENIX01 CPU register test in progress02 CMOS read/write failure03 ROM BIOS checksum failure04 Programmable interval timer failure05 DMA initialization failure06 DMA page register read/write failure08 RAM refresh verification failure09 First 64K RAM test in progress0A First 64K RAM chip or data line failure multi-bit0B First 64K RAM odd/even parity logic failure0C Address line failure in first 64K RAM0D Parity failure in first 64K RAM10 Bit 0 first 64K RAM failure11 Bit 1 first 64K RAM failure12 Bit 2 first 64K RAM failure13 Bit 3 first 64K RAM failure14 Bit 4 first 64K RAM failure15 Bit 5 first 64K RAM failure16 Bit 6 first 64K RAM failure17 Bit 7 first 64K RAM failure18 Bit 8 first 64K RAM failure19 Bit 9 first 64K RAM failure1A Bit a(10) first 64K RAM failure1B Bit B(11) first 64K RAM failure1C Bit C(12) first 64K RAM failure1D Bit D(13) first 64K RAM failure1E Bit E(14) first 64K RAM failure1F Bit F(15) first 64K RAM failure20 Slave DMA register failure21 Master DMA register failure22 Master interrupt mask register failure23 Slave interrupt mask register failure25 Interrupt vector loading in progress27 8042 keyboard controller test failure28 CMOS power failure/checksum calculation in progress29 CMOS configuration validation in progress2B Screen memory test failure2C Screen initialization failure2D Screen retrace test failure2E Search for video ROM in progress30 Screen believed running with video ROM31 Mono monitor believed operational32 Color monitor (40 columns) believed operational33 Color monitor (80 columns) believed operational34 Timer tick interrupt in progress or failed (non-fatal)35 Shutdown failure (non-fatal)36 Gate A20 failure (non-fatal)37 Unexpected interrupt in protected mode (non-fatal)38 Memory high address line failure at 01000-0A000 (non-fatal)39 Memory high address line failure at 100000-FFFFFF (non-fatal)3A Timer chip counter 2 failed (non-fatal)3B Time of day clock stopped3C Serial port test3D Parallel port test41 System board select bad42 Extended CMOS RAM badCODURI AMI01 NMI is disabled and the i286 register test is about to start02 i286 register test has passed03 ROM BIOS checksum test (32Kb from F8000h) passed OK04 8259 programmable interrupt controller has initialized OK05 CMOS interrupt disabled06 Video system disabled and the system timer checks OK07 8253/4 programmable-interval timer test OK08 Delta counter channel 2 OK09 Delta counter channel 1 OK0A Delta counter channel 0 OK0B Parity status cleared0C The refresh and system timer check OK0D Refresh check OK0E Refresh period checks OK10 Ready to start 64KB base memory test11 Address line test OK12 64KB base memory test OK13 System-interrupt vectors initialized14 8042 keyboard controller checks OK15 CMOS read/write test OK16 CMOS checksum and battery OK17 Monochrome video mode OK18 CGA color mode set OK19 Attempting to pass control to video ROM at C0000h1A Returned from video ROM1B Display memory read/write test OK1C Display memory read/write alternative test OK1D Video retrace test OK1E Global equipment byte set for proper video operation1F Ready to initialize video system20 Video test OK21 Video display OK22 The power-on message is displayed30 Ready to start the virtual-mode memory test31 virtual memory mode test started32 CPU has switched to virtual mode33 Testing the memory address lines34 Testing the memory address lines35 Lower 1MB of RAM found36 Memory size computation checks OK37 Memory test in progress38 Memory below 1MB is initialized39 Memory above 1MB is initialized3A Memory size is displayed3B Ready to test the lower 1MB of RAM3C Memory test of lower 1MB OK3D Memory test above 1MB OK3E Ready to shutdown for real-mode testing3F Shutdown OK- now in real mode40 Ready to disable gate A2041 A20 line disabled successfully42 Ready to start DMA controller test4E Address line test OK4F System still in real mode50 DMA page register test OK51 Starting DMA controller 1 register test52 DMA controller 1 test passed, starting DMA controller 2 register test53 DMA controller 2 test passed54 Ready to test latch on DMA controller 1 and 255 DMA controller 1 and 2 latch test OK56 DMA controller 1 and 2 configured OK57 8259 programmable interrupt controller initialized OK58 8259 programmable interrupt controller mask register OK59 Master 8259 programmable interrupt controller mask register OK5A Ready to check timer interrupts5B Timer interrupt check OK5C Ready to test keyboard interrupt5D Error detected in timer or keyboard interrupt5E 8259 programmable interrupt controller error5F 8259 programmable interrupt controller OK70 Start of keyboard test71 Keyboard controller Ok72 Keyboard tested OK73 Keyboard global initialization OK74 Floppy setup ready to start75 Floppy controller setup OK76 Hard disk setup ready to start77 Hard disk controller setup OK79 Ready to initialize timer data7A Verifying CMOS battery power7B CMOS battery verified OK7D Analyzing CMOS RAM size7E CMOS memory size updated7F Send control to adapter ROM80 Enable the setup routine if is pressed82 Printer data initialization is OK83 RS-232 data initialization is OK84 80x87 check and test OK85 Display any soft-error message86 Give control to ROM E0000h87 Return from system ROM00 Call the Int19 boot loader Codul sonor de eroare... - 1 beep: eroare la reimprospatarea memoriei; verifica DRAM-urile.- 2 beep-uri: eroare de paritate; memorii defecte.- 3 beep-uri: eroare RAM; memoria nu poate fi scrisa sau citita.- 4 beep-uri: ceasul sistemului nu functioneaza; eroare foarte grava.- 5 beep-uri: eroare CPU; procesorul nu functioneaza corect. - 6 beep-uri: eroare la controlerul tastaturii; procesorul nu trece in mod virtual.- 7 beep-uri: eroare semnalata de procesor in logica intreruperilor.- 8 beep-uri: eroare la citirea/scrierea memoriei video; placa grafica lipsa sau defecta.- 9 beep-uri: ROM-bios defect.- 10 beep-uri: eroare la registrul de "shutdown" al CMOS-ului.- 11 beep-uri: eroare in cache-ul L2; chipurile chache-ului extern sunt defecte.- 2 beep-uri scurte: eroare in procesul POST; esec in testarea hardware-ului.- 1 beep lung si 2 scurte: probleme la hardware-ul grafic (de obicei la baleiaj).- 1 beep lung si 3 scurte: eroare la placa grafica (RAMDAC, memorie grafica, monitor).