Catalog piese metalice Glulam

8/10/2019 Catalog piese metalice Glulam

http://slidepdf.com/reader/full/catalog-piese-metalice-glulam 1/24

Glulam

Timber

Connectors

The following information refersto connectors suitable for use in

Glulam timber construction.

C-GLULAM-0711

Issued July 2011



Glulam Connectors

Contents

Page 3 About Glulam

Page 4 Anchor Bolts and Resins

Page 5 Heavy Duty Post Bases

Page 6 Aluminium Shear Rings

Page 7-14 Concealed Beam Hangers

Page 15-18 Face Fix Hangers

Page 19 Fastenings

0-21 Bespoke Connectors

Page 22-23 Made to Connector Order Forms ®

l l l l

I I

l l l

`



About Glulam

Glulam Connectors

Sustainable, Durable, Beautiful

With the Construction Industry becoming ever more conscious of

environmental issues, companies are taking a fresh look at building

structures and carbon emissions. As a more sustainable material than

steel, Glulam contributes to this goal.

Glulam timbers are being used where steel beams and columns would

have been employed in buildings such as schools, supermarkets and large

commercial buildings.

Simpson Strong-Tie® have designed a range of connectors to help build

Glulam structures safely and economically, by standardising the products

and obtaining CE approval where possible.

The following pages give technical information on the

connectors, including sizes and load capacities,

making life easier for designers and specifiers alike.

For technical queries

please contact:

Telephone: +44(0)1827 255600

Fax: +44(0)1827 255629

Email: [email protected]

For sales enquiries contact our

Engineered Timber Division:

Telephone: +44(0)1827 255604Fax: +44(0)1827 255616




Superplus/Liebig Anchor/BOAX/AT-HP/LMAS

Shown below are the Heavy Duty Anchor Bolts and Concrete Resin products which are suitable foruse in Glulam Timber applications:

Glulam Connectors

Anchor Bolts & Concrete Resins

1. Loads are based on Non-Cracked concrete (C20/25 - C50/60).

2. For further information please refer to Simpson Strong-Tie® Liebig Technical Manual.

3. “Re-bar” drill bits are available on request.

4. Design calculations for all anchors are available on request.

Super Plus BLS

Zinc Coated

Under-cut

Anchor

Super Plus BLS

Stainless Steel

Under-cut

Anchor

AS Anchor

Stainless

Steel Anchor

with hex head

screw and domed

washer

AB Anchor

Stainless

Steel Anchor

with hex nut,

domed washer

and threaded

stud.

BOAX

Throughbolt

with hex nut

and washer.

LMAS

Threaded Stud

with hex nut

and washer.

Chemical Anchors

A range of styrene

free and pure epoxy

resins.

Range Material Approval Thread

Size

Drill Hole

Ø(mm)

Permissable Load Range

Tension Shear

Superplus

BLS

Grade 8.8 Carbon Steel

Zinc Plated

ETA-01/0011

(Option 1)

M18 14 6.1 -10.8 6.1 - 23.7

M12 20 17.2 - 28.4 34.4 - 40.0

M16 25 44.1 - 53.0 67.4

A4-80 Stainless SteelETA-05/0013

(Option 1)

M8 14 6..1 - 13.1 6.1 - 24.0

M12 20 17.2 - 30.1 34.4 - 48.5

M16 25 44.1 - 56.1 88.2 - 90.7

Liebig

Anchor


Zinc Plated

ETA-06/0123

(Option 1)

M10 15 9.5 - 14.8 22.3

M12 20 17.1 - 26.6 34.3

M16 25 24.0 - 37.2 48.0 - 54.9

A4-80 Stainless Steel (Type AB)

A4-70 Stainless Steel (Type AS)

M10 15 7.1 - 11.0 7.1 - 11.0

M12 20 10.7 - 15.8 24.6 - 28.9

M16 25 16.0 - 23.7 40.0 - 49.5

BOAX

Carbon Steel

Zinc Plated

ETA-08/0276

(Option 1)

M10 10 6.3 - 8.1 8.7

M12 12 7.9 - 10.1 11.0

M16 16 16.7 - 21.4 21.0

A4 Stainless SteelETA-08/0276

(Option 1)

M10 10 6.3 - 8.1 8.7

M12 12 7.9 - 10.1 11.0

M16 16 16.7 - 21.4 21.0

AT-HP/LMAS


Zinc Plated

ETA-09/013

(Option 7)

M12 14 24.8 - 29.3 23.4

M16 18 26.9 - 31.8 36.6

M20 24 39.7 - 46.8 52.6

A4-70 Stainless Steel ETA Pending

M12 14 24.8 25.2

M16 18 26.9 39.4

M20 24 39.7 56.8

4



PBH and PISBMAXI

Heavy duty elevated post bases to suit various sizes of timber and Glulam post. Non-standardsizes to order. Dowels are supplied with the Post Base.

Model Number

Dimensions (mm)

Lower Plate Top Plate Flitch Plate HeightW2 B2 W1 B1 Fv Fh

PBH75 100 160 75 75 110 45 200

PBH120 155 155 120 120 110 90 200

PISBMAXIG-B 200 200 120 120 105 90 118

1. Non-standard sizes are available to order.2. Dowels are supplied with the post base.

Type

Fasteners

Base Post

Qty Type Ø (mm) Qty Type Ø (mm)

PBH75 2 Bolt 12 2 Dowel 8

PBH120 4 Bolt 12 4 Dowel 8PISBMAXIG-B 4 Bolt 16 2 Dowel 12

Dimensions

Fastenings

Material:

• 8mm mild steel plate fin, top plate and bottom

plate.

• 42mm diameter mild steel tube.

• Post bases allow for a rigid fixing of the post to

the ground whilst protecting the end timber from

moisture.

• Post bases are fully hot dipped galvanised.

• Post to foundation connectors made to

customer’s design.

Fv

W1 B1

W2

B2

H

Fh

Glulam Connectors

Heavy Duty Post Bases

▼

▼

F1

F2

▼ F3

▼F4

Model Number

Characteristic Loads (kN)

Download (F1 ) Uplift (F2 ) Lateral (F3 ) Lateral (F4 )

Timber Steel Timber Steel Timber Steel Timber Steel

PBH75 170 109 7.8 8.6 5.3 3.9 5.3 3.8

PBH120 219 109 20.7 22.8 7.7 3.9 7.6 3.8

PISBMAXIG-B 272.2 256.9 42.1 - 27.5 14.1 12.3 -

Performance Data

Bespoke flitch plate and stand off design and manufacturing service available - see pages 22-23.



CBH

The CBH hanger is a development of the TU range. It allows for concealed timber to timberconnections and can be face fixed or pocketed on to the header timber.

ModelNo.

MinimumJoist

Height

ConnectorDimensions

FastenersCharacteristic Capacity (kN)

Dowel Embedment Length (mm)

W H BHeader Nails Joist Dowels

60 80 100 120 140 160

Qty Type Qty Ø

Standard Installation (Slope = 0° )

CBH150/2,5 190 60 150 113.5 14 4.0 X 60 5 10 17.96 18.63 20.65 22.40 24.00 24.00

CBH180/2,5 220 60 180 113.5 16 4.0 X 60 6 10 24.98 26.45 29.54 32.07 32.63 32.63

CBH220/2,5 250 60 220 113.5 22 4.0 X 60 7 10 32.61 34.24 37.90 41.11 42.83 42.83

Slope = 15°

CBH150/2,5 190 60 150 113.5 14 4.0 X 60 5 10 17.31 17.86 19.63 21.22 22.90 23.26

CBH180/2,5 220 60 180 113.5 16 4.0 X 60 6 10 23.97 25.22 28.03 30.47 31.76 31.76

CBH220/2,5 250 60 220 113.5 22 4.0 X 60 7 10 31.36 32.71 35.95 38.91 41.58 41.58

Slope = 30°

CBH150/2,5 190 60 150 113.5 14 4.0 X 60 5 10 16.73 17.16 18.68 20.08 21.59 22.49

CBH180/2,5 220 60 180 113.5 16 4.0 X 60 6 10 23.08 24.12 26.58 28.82 30.81 30.81

CBH220/2,5 250 60 220 113.5 22 4.0 X 60 7 10 30.38 31.49 34.30 36.96 39.72 40.37

Slope = 45°

CBH150/2,5 190 60 150 113.5 14 4.0 X 60 5 10 16.35 16.71 18.03 19.28 20.64 21.91

CBH180/2,5 220 60 180 113.5 16 4.0 X 60 6 10 22.50 23.39 25.59 27.64 29.74 30.07

CBH220/2,5 250 60 220 113.5 22 4.0 X 60 7 10 29.84 30.80 33.32 35.73 38.28 39.52

1. 4.0 x 60 refers to CNA 4,0 x 60 Annular Ring Shank Nail

W

H

B

W

H

B

W

H

B

CBH150 CBH180 CBH220

Glulam Connectors

Concealed Beam Connectors

Material: 2.5mm Pre-Galvanised Steel

Order nails and dowels separately.

B

H H

H

B

B



ModelNo.

MinimumJoist

Height

ConnectorDimensions



W H BHeader Nail Joist Dowels

60 80 100 120 140 160Qty Type Qty Ø

Standard Installation (Slope = 0° and Skew = 0° )

BTALU90-B 142 62 86 103 16 4.0 x 60 4 8 10.30 11.30 12.4 13.20 13.20 13.20

BTALU120-B 172 62 116 103 24 4.0 x 60 3 12 18.10 18.70 19.80 21.20 22.70 24.30

BTALU160-B 212 62 156 103 32 4.0 x 60 4 12 29.80 30.70 23.30 34.40 36.80 39.30

BTALU200-B 252 62 196 103 40 4.0 x 60 5 12 42.70 43.80 46.00 48.90 52.20 55.60

BTALU240-B 292 62 236 103 48 4.0 x 60 6 12 56.00 57.30 60.20 63.90 68.20 72.60

Slope = 15°

BTALU90-B 142 62 86 103 16 4.0 x 60 4 8 10.30 11.30 12.40 13.20 13.20 13.20

BTALU120-B 172 62 116 103 24 4.0 x 60 3 12 17.50 18.00 18.90 20.10 21.40 22.90

BTALU160-B 212 62 156 103 32 4.0 x 60 4 12 28.90 29.50 30.90 32.70 34.70 36.90

BTALU200-B 252 62 196 103 40 4.0 x 60 5 12 41.50 42.30 44.10 46.60 49.40 52.40

BTALU240-B 292 62 236 103 48 4.0 x 60 6 12 54.00 55.70 58.10 61.20 64.90 68.80

Slope = 30°

BTALU90-B 142 62 86 103 16 4.0 x 60 4 8 10.30 11.30 12.40 13.20 13.20 13.20

BTALU120-B 172 62 116 103 24 4.0 x 60 3 12 17.00 17.30 18.10 19.10 20.30 21.50

BTALU160-B 212 62 156 103 32 4.0 x 60 4 12 28.00 28.70 29.90 31.40 33.20 35.10

BTALU200-B 252 62 196 103 40 4.0 x 60 5 12 40.30 41.50 43.10 45.20 47.60 50.30

BTALU240-B 292 62 236 103 48 4.0 x 60 6 12 53.40 55.20 57.20 60.00 63.20 66.60

Slope = 45°

BTALU90-B 142 62 86 103 16 4.0 x 60 4 8 10.30 11.30 12.40 13.20 13.20 13.20

BTALU120-B 172 62 116 103 24 4.0 x 60 3 12 16.50 17.00 17.60 18.50 19.50 20.70

BTALU160-B 212 62 156 103 32 4.0 x 60 4 12 27.50 28.40 29.40 30.80 32.40 34.10

BTALU200-B 252 62 196 103 40 4.0 x 60 5 12 40.30 41.50 42.90 44.80 47.00 49.40

BTALU240-B 292 62 236 103 48 4.0 x 60 6 12 54.10 55.50 57.50 60.00 63.00 66.10

Cross Laminated Timber Connections

BTALU Concealed Beam Hanger

Glulam Connectors



Glulam Connectors


The BTALU concealed hanger is one solution to connecting timber members togetherwithout seeing the connector.

B

H

W

BTALU Installation

BTALU Installed

See oppositefor dowel holepositions.

It is designed to be fixed to the header timber and then fullyinserted into a slot in the in-coming beam, and held in placewith dowels. Holes are drilled through the timber and fin of theBTALU, allowing accurate alignment. This method provides anaesthectically pleasing connection for feature beams.

Material: 6mm Aluminium

Order nails separately.



Glulam Connectors

Concealed Beam ConnectorsGlulam Connectors


BTALU Hole Positions

9

The diagrams to the rightshow recommended holepositions, to be drilled in situ,using a suitable drill bit or selftapping dowel pin.

6

6



Cross Laminated Timber ConnectionsGlulam Connectors

Concealed Beam ConnectorsGlulam Connectors


0

ATF Concealed Beam Hanger The ATF hanger is a concealed timber to timber hanger which allows for a strong connection

between the two timbers without the hanger being seen.

Model

No.

MinimumJoist

Height

ConnectorDimensions Fasteners

CharacteristicCapacity (kN)

W HHeader Nails Joist Screws

DownloadQty Type Qty Type


ATF55/110-B 140 55 110 8 4.0 X 60 11 9555000 5.5

ATF55/150-B 180 55 150 11 4.0 X 60 15 9555000 7.5

ATF55/190-B 220 55 190 14 4.0 X 60 21 9555000 10.5

ATF75/150-B 180 75 150 17 4.0 X 60 22 9555000 11.0

ATF75/190-B 220 75 190 21 4.0 X 60 28 9555000 14.0


2. 9555000 refers to CSA 5,0 x 50 Connector Screw with a reduced head height

The first part of the connector is fixed into a pocket on the header timber with nails and the second part is fitted

on the end of the in-coming beam with screws. No slots or dowel holes are necessary, speeding up production.

Material: 5mm Pre-Galvanised Steel

Order nails and screws separately.

W

H



TU Concealed Beam Hanger

This 3.5mm thick galvanised steel, load rated hanger provides an aesthetically attractiveconnection for exposed beams. Mild steel dowels and screws are included.

Glulam Connectors

Concealed Beam Hangers

TU20 (other sizes similar)

U.S. Patent 5,062,733

INSTALLATION:

• Dowels aligned across the grain may cause splitting if the wood shrinks excessively. Use

only in glulam, composite timber or well dried timber. Verify that the header can take the

required fasteners specified in the table.

• Attach to the supporting beam with 5.0 x 40mm screws (supplied).

• Specify dowel length and TU size to fit the application.

• Preparation of carried beam is best done off-site with cutting and boring tools.

• Holes in beam should be same diameter as dowel to ensure tight fit.

• Centre the TU within height of carried beam.

• Centre dowels within the width of the carried member

• For a sloped installation the TU hanger remains as standard and the timber is cut and

angled to suit the slope.

• Recommended for internal dry environments (service class 1 & 2)

OPTIONS: Contact Simpson Strong-Tie for details of special installation tools.

• The standard install will leave a 5mm gap between carried and supporting beams.

• Pocket installation gives a fully concealed connection. See next page.

• Skewed installation up to 60°. Sloped installation maximum 45°.

• Options: Skewed TU available. To be factory ordered.

• Additional screws are available to order.

ModelNo.

MinimumJoist

Height

ConnectorDimensions



W H BHeader Screw Jois t Dowels

60 80 100 120Qty Type Qty Ø


TU12 120 40 96 101 6 5.0 X 40 4 8 7.8 8.4 9.1 9.5

TU16 160 60 134 108 18 5.0 X 40 3 12 19.0 19.4 20.1 21.1

TU20 200 60 174 108 22 5.0 X 40 4 12 27.5 28.0 29.0 30.4

TU24 240 60 214 108 26 5.0 X 40 5 12 36.1 36.7 38.0 39.7

TU28 280 60 254 108 30 5.0 X 40 6 12 44.7 45.4 47.0 48.9

Skewed Installation (Slope = 0° and Skew = 60° )

TU12 120 40 96 101 6 5.0 X 40 4 8 6.7 7.3 8.0 8.4

TU16 160 60 134 108 18 5.0 X 40 3 12 15.6 16.0 16.7 17.5

TU20 200 60 174 108 22 5.0 X 40 4 12 23.5 24.0 25.0 26.3

TU24 240 60 214 108 26 5.0 X 40 5 12 31.9 32.6 34.0 35.8

TU28 280 60 254 108 30 5.0 X 40 6 12 40.7 41.6 43.4 45.6

Sloped Installation (Slope = 45° and Skew = 0° )

TU12 160 40 96 101 6 5.0 X 40 4 8 7.8 8.4 9.1 9.5

TU16 190 60 134 108 18 5.0 X 40 3 12 18.1 18.5 19.0 19.6

TU20 225 60 174 108 22 5.0 X 40 4 12 26.3 26.9 27.6 28.5

TU24 260 60 214 108 26 5.0 X 40 5 12 34.8 25.6 36.4 37.6

TU28 295 60 254 108 30 5.0 X 40 6 12 43.3 44.2 45.3 46.7

Skewed and Sloped Installation (Slope = 45° and Skew = 60° )

TU12 160 40 96 101 6 5.0 X 40 4 8 6.5 6.9 7.3 7.9

TU16 190 60 134 108 18 5.0 X 40 3 12 16.3 16.6 17.0 17.5

TU20 225 60 174 108 22 5.0 X 40 4 12 24.3 24.8 25.4 26.1

TU24 260 60 214 108 26 5.0 X 40 5 12 32.9 33.6 34.4 35.5

TU28 295 60 254 108 30 5.0 X 40 6 12 42.0 42.9 43.9 45.3

Glulam Connectors


1. 5.0 x 40 refers to CSA 5,0 x 40 Connector Screw

Material: 3.5mm Pre-Galvanised Mild Steel. Dowels: Mild Steel Electroplated Zinc coating.

2



Skew Angle

Beam-to-Post Beam-to-Beam SkewedBeam-to-Beam

SlopedBeam-to-Beam

SlopedBeam-to-Beam

INSTALLATION PROCEDURE FOR A TU CONCEALED CONNECTOR:

ATTACH CONNECTOR TO HEADER

• Position the connector at the pre determined height and screw the connector to the header or post.•

Fill all holes with screws supplied.

PREPARE THE BEAM

• Cut the beam to the length specified.• Cut a slot into the end of the beam. Slot width for TU12 is 6mm and 9mm for all others.

• Cut the slot 3mm deeper than the TU and short of the beam height for concealed connector. This allows the connector tobe hidden from below. Otherwise cut the slot 3mm deeper than the TU and through the entire beam height.

• Fully Concealed Only: Rout a pocket into the beam end. The pocket should be 6mm deep. Enough to hide the thicknessof the TU and the screw heads. This eliminates the gap between the beam & header (see Pocket Installation Illustration).

DRILL BEAM DOWEL HOLES

• Position drill guide to provide the proper dowel end distance & height. Clamp in place (Drill guide available from Simpson

Strong-Tie).• Drill the dowel holes to the required diameter. Dowel hole diameter for the TU12 is 8mm and 12mm for all others.

INSTALL BEAMS

• Install top dowel into the carried beam first. Slip beam into place and install the remaining dowels working from the topdownwards.

• Fully Concealed Only: To hide exposed dowel holes when the installation is complete, glue and plug the holes.

POCKET (CONCEALED)

TU12

STANDARD INSTALLATION

Glulam Connectors

Concealed Beam Connectors (TU)

13



TU Supporting Timber Rotated About Axis

Glulam Connectors

Concealed Beam HangersGlulam Connectors


The TU connectors can be used to support timbers rotated about their axis - e.g. purlins.

HangerModel

No.

MinimumJoist

Height(mm)

Characteristic Lateral Capacity (kN)


60 80 100 120

TU12 120 1.5 2.0 2.5 3.0

TU16 160 2.0 2.6 3.3 4.0

TU20 200 2.7 3.5 4.4 5.1

TU24 240 3.4 4.4 5.3 6.4

TU28 280 4.3 5.3 6.4 7.7

1. Values are based on C24 timber grade.

2. Lateral Loads can only be applied to connections with no slope or skew.

3. The following design check must be completed if combined loads are applied at the same time.

≤ 1F1,d

2

R 1,d

F2,d 2

R 2,d

F3,d 2

R 3,d( ( () )) + +

Applied Load



1. 3.75 x 30mm square twist nails available on request.

Timber SectionModel

No.

Dimensions (mm) Number of Fasteners

(3.75 X 30mm)Characteristic Capacity (kN)

W H BW H Header Joist Download Uplift

65

180 SAE380/66/2 66 157 84 22 12 8.8 7.7

225 SAE500/66/2 66 218 84 34 18 17.2 14.5

270 SAE500/66/2 66 218 84 34 18 17.2 14.5

315 SAE500/66/2 66 218 84 34 18 17.2 14.5

90

225 SAE500/91/2 91 205 84 34 18 17.2 14.5

270 SAE500/91/2 91 205 84 34 18 17.2 14.5

315 SAE500/91/2 91 205 84 34 18 17.2 14.5

360 SAE590/91/2 91 265 75 40 22 20.8 18.0

405 SAE590/91/2 91 265 75 40 25 20.8 18.0

115

315 SAE620/116/2 116 252 75 40 22 20.8 18.0

360 SAE620/116/2 116 252 75 40 22 20.8 18.0

405 SAE620/116/2 116 252 75 40 22 20.8 18.0

Glulam Connectors


Face Fix Hangers

SAE Heavy Duty Face Fix Hanger

The SAE is a heavy duty hanger designed for face fix applications which require additional strength.

• SAE hangers have bolt holes for 12mm fasteners into the face.

• SAE Timber Bolted capacity to be determined according to the relevant standards.

• The hanger depth is to be at least 60% of the carried member depth to preventrotation, unless additional lateral restraint is added to the top of the carriedmember.

INSTALLATION:

• Use all specified fasteners. Verify that the header can take the required fastenersspecified in the table.

• SAE hangers should be installed by filling all round holes with the specifiedfasteners.

OPTIONS:

• Other widths of the SAE hangers are available to order.

• Slope and skew options available as a special SAE hanger without bolt holes.

• Skews right or left maximum 67.5° and slopes up or down maximum 45°.

•

Hangers with skews greater than 15° will have all joist nailing on the outside angle.• Contact Simpson Strong-Tie® technical department for information regarding

sloped and skewed options.

40 Material: 2mm Pre-Galvanised Mild Steel.

15



Timber SectionModel

No.




90

225 SAI500/91/2 91 205 84 28 18 16.80 14.3

270 SAI500/91/2 91 205 84 28 18 16.80 14.3

315 SAI500/91/2 91 205 84 28 18 16.80 14.3

360 SAI620/91/2 91 265 75 40 22 20.80 18.0

405 SAI620/91/2 91 265 75 40 22 20.80 18.0

115

315 SAI620/116/2 116 252 75 40 22 20.80 18.0

360 SAI620/116/2 116 252 75 40 22 20.80 18.0

405 SAI620/116/2 116 252 75 40 22 20.80 18.0

Glulam Connectors


Face Fix Hangers

SAI Heavy Duty Face Fix Hanger

The SAI is a heavy duty hanger designed for face fix applicationswhich require additional strength.

The hanger depth is to be at least 60% of the carried member depth toprevent rotation, unless additional lateral restraint is added to the topof the carried member.

Material: 2mm Pre-Galvanised Mild Steel.

INSTALLATION:

• Use all specified fasteners. Verify that the header can take therequired fasteners specified in the table.

• SAI hangers can be installed by filling all round holes with thespecified fasteners.

H

B

W


6



Glulam Connectors

Face Fix Hangers

SDE Width Adjustable Face Fix Hanger

The two separate components that make up the SDE system can be adjusted suit a range of joistwidths between 60mm to 120mm. Each SDE is supplied as a pair.

W

B

H

Timber SectionModel

No.




65

180 SDE380/30 30 160 84 22 16 11.5 6.3

225 SDE440/30 30 190 84 28 20 14.3 9.4

270 SDE440/30 30 190 84 28 20 14.3 9.4

315 SDE440/30 30 190 84 28 20 14.3 9.4

90

225 SDE440/30 30 190 84 28 20 14.3 9.4

270 SDE440/30 30 190 84 28 20 14.3 9.4

315 SDE440/30 30 190 84 28 20 14.3 9.4

115 315 SDE440/30 30 190 84 28 20 14.3 9.4

SDE SPECIFICATION

The hanger depth is to be at least 60% of the carried member depth toprevent rotation, unless additional lateral restraint is added at the top of thecarried member.

MATERIAL:

• 2mm pre-galvanised mild steel.

INSTALLATION:

• Use all fasteners as specified in the table below. Check that the headercan accomodate the fasteners specified. Each SDE piece must alsobe nailed through the holes underneath.


17



HGUS Heavy Duty Face Fix Hanger

Timber SectionModel

No.

Dimensions (mm)Number of Fasteners

(4.0 x 100mm nails)

Characterisitc Capacity

(kN)

W H B

W H Header Joist Down Up

90

225 HGUS48N 92 180 100 36 10 20.47 11.06

270 HGUS48N 92 180 100 36 10 20.47 11.06

315 HGUS412N 92 265 100 56 20 33.80 22.11

360 HGUS412N 92 265 100 56 20 33.80 22.11

405 HGUS412N 92 265 100 56 20 33.80 22.11

115

315 HGUS265/115N 115 265 100 56 20 33.80 22.11

360 HGUS265/115N 115 265 100 56 20 33.80 22.11

405 HGUS265/115N 115 265 100 56 20 33.80 22.11

140

360 HGUS5.50/14N 140 316 100 66 22 43.90 24.32

405 HGUS5.50/14N 140 316 100 66 22 43.90 24.32

450 HGUS5.50/14N 140 316 100 66 22 43.90 24.32

495 HGUS5.50/14N 140 316 100 66 22 43.90 24.32

HGUS is a one piece joist hanger for supporting solid compositebeams from timber members.

Glulam Connectors


Face Fix Hangers

Double shear nailing allows distribution of the carriedmember’s load through two points on each nail forgreater strength.

MATERIAL:

2.5mm pre-galvanised mild steel.

INSTALLATION:

Use all specified fasteners. Verify that the header cantake the required fasteners specified in the table.

100mm nails must be driven at 45° into joist domeor pan nails holes, through carrying member andinto the carried member to achieve the table loads.

The required nails are supplied with the hanger.


B




Glulam Connectors

Fastenings

BoltsGrade 8.8 in accordance with EN ISO 4014 or EN ISO 4017

Item Code Diameter (mm)Overall

Length (mm)

M12/80

12

80

M12/100 100

M12/120 120

M12/140 140

M12/160 160

M12/180 180

M12/200 200

M12/220 220

M12/240 240

M12/250 250

M16/120

16

120

M16/140 140

M16/160 160

M16/180 180

M16/200 200

M16/220 220

M16/240 240

M16/250 250

M20/120

20

120

M20/140 140

M20/160 160

M20/180 180

M20/200 200

M20/220 220

M20/240 240

M20/250 250

DowelsIn accordance with EN14592:2009

Item Code Diameter (mm)Overall

Length (mm)

STD8X60-B

8

60

STD8X80-B 60

STD8X100-B 100

STD8X120-B 120

STD10X60-B

10

60

STD10X80-B 80

STD10X100-B 100

STD10X120-B 120

STD10X140-B 140

STD12X60-B

12

60

STD12X80-B 80

STD12X100-B 100

STD12X120-B 120

STD12X140-B 140

STD12X160-B 160

STD12X180-B 180

STD12X200-B 200

STD16X120-B

16

120

STD16X140-B 140

STD16X160-B 160

STD16X180-B 180

STD16X200-B 200

STD20X120-B

20

120

STD20X140-B 140

STD20X160-B 160

STD20X180-B 180

STD20X200-B 200

Hex NutsGrade 8 in accordance with EN ISO 4032 or EN ISO 780

Item Code Description Material

M12 NUT Hex Nut: M12

MildSteel



WashersIn accordance with EN1995-1-1

Item CodeOutside

Diameter (mm)

Inside

Diameter (mm)

Thickness

(mm)

WASHER36/13/3.6 36 13 3.6

WASHER48/17/4.8 48 17 4.8

WASHER60/21/6 60 21 6

19



Glulam Connectors

Fabrication Service

Bespoke Connectors

Due to the nature of Glulam construction, there are occasions when standard products will not be sufficient. To this

end, Simpson Strong-Tie® operates a speedy fabrication service to manufacture connectors for customers which

have either been designed by Architects, Designers and Structural Engineers, or are based on a full design and

manufacturing service provided by Simpson Strong-Tie®, on provision of dimensional and loading information.

These items can be as diverse as large heavy duty post bases, moment plates or small, but heavy duty

angle brackets.

Email or Fax:

Fax: +44(0)1827 255629


Simpson Strong-Tie®, Winchester Road, Cardinal Point, Tamworth, Staffordshire, B78 3HG

Visit: www.strongtie.co.uk/fabrication

l

I

i

ii l

l

I

i

ii l

l

I

i

ii l

l

To ensure we quote effectively for our fabrication only service, please provide as much information as possible, including:

• Drawing (CAD file if available)• Material size and specification

• Tolerances (general tolerance of +/- 1mm will be applied unless otherwise stated)

• Coating requirement (type and thickness)

• Quantity

• Date Required

Connectors manufactured via this service will be accompanied by the standard "Disclaimer".

To ensure we quote effectively for our post base design and fabrication service, we will require some basic dimensional and loading

information - see individual products in the following sections for further details. Minimum required information is indicated with *.

Due to a wide range of design possibilities, a reliable lead time can only be provided when designs are approved.



Fabricated Knee and Apex Moment Plates

Glulam structures often require moment plates to connect the timbers together, whether it be at the apex of a

roof or at a post/beam intersection ( see drawing above).

Simpson Strong-Tie® offers a fabrication service to manufacture the plates to the customers requirements, and

supply the fixings to secure it in place.

Please contact our Technical Department, with the details of the structure to be connected.

Telephone: +44(0)1827 255600

Fax: +44(0)1827 255629


Visit: www.strongtie.co.uk/glulam

Knee Joint

Apex Joint

See Page 5 & 22/23

Glulam Connectors

Moment Plates



Special PBG Post Base (Flitch Plate) Order

Name:Qty Required:

Company Name:

Telephone Number:Date Required:

Email Address:

Complete and Fax to: 01827 255629

Office Use Only Reference No: Manufacturing Cost: Selling Price:

Width of Timber Post * mm

Depth of Timber Post * mm

Grade of Timber Post *

Load Duration **

Downward Applied Load * F1 kN

Upward Applied Load * F2 kN

Lateral Applied Load * F3 kN


Width 1 of Post W1 mm

Width 2 of Post W2 mm

Diameter of Fixing Bolt D mm

Thickness of Flitch Plate Ft mm

Width of Flitch Plate Fh mm

Height of Flitch Plate Fv mm

Thickness of Base Plate Bt mm

Height to Dowel Holes Hh mm

Distance to First Dowel Hole Hw mm

Spacing Between Dowel Holes Hs mm

Diameter of Dowel Holes d mm

Number of Dowel Holes N

Grade S250 in accordance with EN10346

Indicate materialrequired. Supplied in

S250 by default.Grade S275 in accordance with EN10346


Post bases will zinc coated with a thicknessof 55 µm unless otherwise specified.

** Load duration type assumed Long Term for F1 and Short Term for

F2, F3 and F4 unless otherwise stated. Please add "S" for safe workingloads or "C" for charateristic loads after the duration figure.

▼F4



Name:Qty Required:

Company Name:

Telephone Number:Date Required:

Email Address:

Special PBH Post Base (Stand Off) Order

Complete and Fax to: 01827 255629

Width of Timber Post * mm

Depth of Timber Post * mm

Grade of Timber Post *

Load Duration**

Downward Applied Load * F1 kN

Upward Applied Load * F2 kN



Height of Upstand Post * H mm

Width of Base Plate W2 mm

Breadth of Base Plate B2 mm

Thickness of Base Plate t1 mm

Width of Top Plate W1 mm

Breadth of Top Plate B1 mm

Thickness of Top Plate t2 mm

Diameter of Fixing Bolt Holes D1 mm

Office Use Only Reference No: Manufacturing Cost: Selling Price:

Diameter of Dowel Holes D2 mm

Width of Flitch Plate Fh mm

Height of Flitch Plate Fv mm

Thickness of Flitch Plate t3 mm

Section of Upstand Post Pd mm

Height to Dowel Holes dv1 mm

Spacing Between Dowel Holes dv2 mm

Dist. Top of Flitch Plate to Dowel Holes dv3 mm

Dist. to First Column of Dowel Holes dh1 mm

Spacing Between Columns of Dowel Holes dh2 mm

Please Select The Steel Specification from the list Below:


Indicate material

required. Supplied inS250 by default.Grade S275 in accordance with EN10346


Post bases will zinc coated with a thicknessof 55 µm unless otherwise specified.

B1

B2

W1 W2

** Load duration type assumed Long Term for F1 and Short Term for

F2, F3 and F4 unless otherwise stated. Please add "S" for safe working

loads or "C" for charateristic loads after the duration figure.



GlulamTimber

ConnectorsFor further information and technical

support regarding the Glulam

connector range contact:

Simpson Strong-Tie

Winchester Road

Cardinal Point

Tamworth

Staffordshire

B78 3HG

Telephone +44(0)1827 255600

Email: [email protected] Visit: www.strongtie.co.uk/glulam

®

Catalog piese metalice Glulam

Documents

Transcript of Catalog piese metalice Glulam