Post on 02-Jun-2018
8/10/2019 Catalog Accesorii Incendiu
1/105
GE Security
FIRE SYSTEM ACCESSORIES
Product catalogue
8/10/2019 Catalog Accesorii Incendiu
2/105
ASPIRATION SYSTEMS
8/10/2019 Catalog Accesorii Incendiu
3/105
Page 2
Aspiration Systems
Technical Data
Protection IP54
Housing ABS
Operating temperature -20C to +50C
Dimensions 300 x 150 x 110 mm
Ordering Information
DD700 Single pipe universal duct detector
One-tube air sampling system
Conventional or analogue detectors
Test hole on cover
Simple installation
Sensitive flow indication
Filter for dusty environments
Simple service and maintenance
Installer-friendly connection of cables
Foolproof installation of sampling tube
Optional booster fan
Special profile for 700 series and 2000 series detectors
Special profile for 300 series and 1500 series detectors
Single pipe universal duct detector DD700
8/10/2019 Catalog Accesorii Incendiu
4/105
General
The ASD20 Aspiration Smoke Detector consists of an analysis chamber with
one or two smoke detectors, which can be of conventional or analogue
technology, ionisation or optical. The smoke reaches the analysis chamber
through the installation pipes after having been sucked in by a turbine inside
the ASD20 system. An electronic circuit controls said turbine and the air flow,
giving off a fault signal if the pipes are broken or if the air intake is
obstructed. It has two voltagefree relays for local manoeuvres, one per
detector, and a third system fault relay. When analogical smoke detectors
from the 700A series are used, it is possible to adjust their sensitivity levels
from the fire control unit.
Technical Data
Power supply voltage 24 V
Consumption on standby 250 mA
Consumption 1st alarm 280 mA
Consumption 2nd alarm 320 mA
Fault consumption 220 mA
Working temperature -10 to +60C
Storage temperature -10 to +70C
Relative humidity
8/10/2019 Catalog Accesorii Incendiu
5/105
Page 4
Aspiration Systems
The FASD710 provides a low cost solution for aspiration systems using pointsmoke detectors. The controller can be used in many applications where point
smoke detectors are not suitable. The powerful pump allows pipe distances of
up to 50 metres
Technical Data
Supply voltage 24V DC
Current consumption 225mA
Number of detectors (not included) 2
Filtration Cartridge dust particle filter
Maximum tube length 50m
IP rating IP65
Ordering Information
FASD710 High-performance aspiration controller for point detectors
FHSD771 Large bore red pipe 3 metre length
FHSD772 Straight union large bore
FHSD774 45 deg. elbow for large bore pipes
FHSD775 End cap for large bore pipes
FASD710
2 detectors for redundancy and mixed detection strategy.
Up to 50 metres pipe
Cartridge air filter
Bar graph indication of flow
high / low flow fault and remote reporting
IP65 rating
Hotels
Banks
Hospitals
Livestock Buildings
Prisons
Underground stations
Aesthetic environments
Harsh environments
Dirty environments
High-performance aspiration controller for point detectors FASD710
8/10/2019 Catalog Accesorii Incendiu
6/105
Page 5
Aspiration Systems
Compact and powerful, the FHSD720 has all the detection and monitoringfeatures of big aspiration systems. It is ideal for monitoring localised areas
up to 850m. All data can be uploaded or downloaded via the standard RS232
or RS485 ports
Technical Data
Power supply 24V, 600ma min, 1,5A max
Smoke detector Resolution 0.005%, range 20%
Light source 50mW 660nm high power laser diode
Number of inlets 2 (ground and ceiling), 1 address
Pipe size 25mm Oudside Diameter
Pipe lenght 70 meters
Aspirator 800Pa static pressure
Area coverage 850m
Alarm levels 4: alert, action, fire1, fire2Alarm setting range 0.005% - 20.0%
Outputs 4 alarm relays, 1 fault relay, 1A change over
Communication RS232, Modbus, RS485
Weight 3kg
Humidity 0-95%
Temperature 0 - 50 C
Ordering Information
FHSD720 Localised aspirated early warning smoke detection system
FHSD720RL Relay Module 4 Channel for FHSD72x
FHSD732 Single channel remote disp lay & programmer
FHSD733 Remote display repeate r un it - 16 un its
FHSD751 Filter+ with fi lter element - harsh environmentFHSD754 Rep lacement f il te r e lement for the FHSD751
FHSD771 Large bore red pipe 3 metre length
FHSD772 Straight union large bore
FHSD773 90 deg. bend for large bore pipes
FHSD774 45 deg. elbow for large bore pipes
FHSD775 End cap for large bore pipes
IP65
RS232 and RS485 standard
High Power Pump
High sensitivity laser detector
Four alarm levels
Remote display units
24V operation
Fault monitoring
Small EDP rooms
Server rooms
Escalators
Machine protection
Localised aspirated early warning smoke detection system FHSD720
8/10/2019 Catalog Accesorii Incendiu
7/105
Page 6
Aspiration Systems
The FHSD721 and FHSD721D four pipe aspirating laser detector systemprovides very early warning to smoke over a very large area. Each pipe can be
up to 100 metres long. The FHSD721D is complete with display, programmer
and web server.
Technical Data
Power supply 24V, 600ma min, 1.5A max
230V 5A PSU and battery charger, optional
Smoke dectector Resolution 0.005%, range 20%
Light source 50mW 660nm high power laser diode
Expected lifetime 10 years
Number of inlets 4 (non addressable)
Pipe size 25mm outside diameter
Pipe length 100 meters each
Aspirator 2000Pa high vacuum centrifugal blowerAlarm levels 4: alert, action, fire1, fire2
Alarm setting range 0.005% - 20.0%
Alarm delay 0 - 60 secs, individually programmable
Outputs 4 alarm relays, 1 fault relay, 1A c/o
Communication RS232, Modbus RS485
Webserver option (FHSD721D only) Ethernet 10 BaseT/RS232 MODEM, TCP / IP
Weight 24V: 10.7 kg, 230V PSU: 14.5 kg
Humidity 0 - 95 %
Temperature 0 - 50 C
Ordering Information
FHSD721 Four pipe, one address aspirated early warning smoke detection system
FHSD721D 4 pipe 1addr. aspir. early warning smoke detection system c/w displayFHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215
FHSD720RL Relay Module 4 Channel for FHSD72x
FHSD731 Conversion kit for remote display
FHSD732 Single channel remote disp lay & programmer
FHSD733 Remote display repeate r un it - 16 un its
FHSD751 Filter+ with fi lter element - harsh environment
FHSD754 Rep lacement f il te r e lement for the FHSD751
FHSD771 Large bore red pipe 3 metre length
FHSD772 Straight union large bore
FHSD773 90 deg. bend for large bore pipes
FHSD774 45 deg. elbow for large bore pipes
FHSD775 End cap for large bore pipes
Early warning applications
Detection with high airflows
Unobtrusive detection
Ideal for large open areas
For inaccessible areas
For dusty and humid environments
For tamperproof installations
Webserver optional
Four pipe, one address aspirated early warning smoke detection system FHSD721
8/10/2019 Catalog Accesorii Incendiu
8/105
Page 7
Aspiration Systems
The FHSD724 four channel large bore aspirating laser detector systemprovides very early warning to smoke over a very large area. Each pipe can be
up to 100 metres long. The unit is complete with display and programmer.
Technical Data
Power supply 24V, 600ma min, 1.5A max
230V 5A PSU / battery charger, optional
Smoke detector Resolution 0.005%, range 20%
Light source 50mW 660nm high power laser diode
Expected lifetime 10 years
Number of inlets 6, fully addressable
Pipe size 25mm outside diameter
Pipe length 100 meter each
Aspirator 2000 Pa high vacuum centrifugal blower
Alarm levels 4: alert, action, fire1, fire2Alarm setting range 0.005% - 20%
Alarm delay 0 - 60 secs, individually programmable
Outputs 4 alarm relays, 1 fault relay, 1A c/o
Communication RS232, Modbus RS485
Web server Communication: Ethernet 10 BaseT/RS232 MODEM,
TCP / IP
Weight 24V: 10.7 kg, 230V PSU: 14.5kg
Humidity 0 - 95%
Temperature 0 - 50 C
Ordering Information
FHSD724D Four channel four area aspirated early warning smoke detection system
FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215
FHSD720RL Relay Module 4 Channel for FHSD72x
FHSD731 Conversion kit for remote display
FHSD732 Single channel remote disp lay & programmer
FHSD733 Remote display repeate r un it - 16 un its
FHSD751 Filter+ with fi lter element - harsh environment
FHSD754 Rep lacement f il te r e lement for the FHSD751
FHSD771 Large bore red pipe 3 metre length
FHSD772 Straight union large bore
FHSD773 90 deg. bend for large bore pipes
FHSD774 45 deg. elbow for large bore pipes
FHSD775 End cap for large bore pipes
Early warning applications
Detection with high inflows
Unobtrusive detection
Ideal for large open areas
For inaccessible areas
For dusty and humid environments
For tamperproof installations
Four channel four area aspirated early warning smoke detection system FHSD724D
8/10/2019 Catalog Accesorii Incendiu
9/105
Page 8
Aspiration Systems
High sensitivity detection
The FHSD726 six channel large bore aspirating laser detector system provides
very early warning to smoke over a very large area. Each pipe can be up to 100
metres long. An environmental detector is also available
Technical Data
Power supply 24V, 600ma min, 1.5A max
Smoke Detector Resolution: 0.005%, range: 20%
Light Source 50mW 660nm high power laser diode
Expected life time 10 years
Number of inlets 6 (fully addressable)
Pipe size 25mm outside diameter
Aspirator 2000Pa high vacuum centrifugal blower
Pipe length 100 meters each
Alarm levels 4
Alarm setting range 0.005% - 20.0%
Alarm delay 1-60 Secs, individually programmable
Outputs 4 alarm relays, 1 A C/O
Communication RS232, Modbus RS485
Web Server Ethernet 10 BaseT/RS232 MODEM, TCP / IP
Environmental
Weight 24V 10.7 KG, 230VPSU 14.5 KG
Humidity 0-95%
Ordering Information
FHSD726D Aspirating laser detector six pipe complete with display
FHSD726DE Aspirating laser and environmental detector, six pipe c/w displayFHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215
FHSD720RL Relay Module 4 Channel for FHSD72x
FHSD731 Conversion kit for remote display
FHSD732 Single channel remote disp lay & programmer
FHSD733 Remote display repeate r un it - 16 un its
FHSD751 Filter+ with fi lter element - harsh environment
FHSD754 Rep lacement f il te r e lement for the FHSD751
FHSD771 Large bore red pipe 3 metre length
FHSD772 Straight union large bore
FHSD773 90 deg. bend for large bore pipes
FHSD774 45 deg. elbow for large bore pipes
FHSD775 End cap for large bore pipes
Early warning applications
Detection with high airflows
Unobtrusive detection
Ideal for large open areas
For inaccessible areas
For dusty and humid environments
For tamperproof installations
Six channel six area aspirated early warning smoke detection system FHSD726
8/10/2019 Catalog Accesorii Incendiu
10/105
Page 9
Aspiration Systems
Selective detection
The FHSD7215D 15 channel micro bore aspirating laser detector system
provides very early warning to smoke over a very large area. Fifteen fully
addressable areas. Each pipe can be up to 50 metres long.
Technical Data
Power supply 24V, 600ma min, 1.5A max
Smoke detector Resolution 0.005%, range 20%
Light source 50mW 660nm high power laser diode
Expected lifetime 10 years
Number of inlets 15, fully addressable
Tube size Micro bore 6mm o.d, 4mm i.d , flexible nylon or FEP
tubing
Aspirator 0.8 bar rotary vane vacuum pump
Pipe length 50 meters each
Alarm levels 4: alert, action, fire1, fire2
Alarm setting range 0.005% - 20.0%
Alarm delay 0-60 seconds, individually programmable
Outputs 4 alarm relays, 1 fault relay, 1A c/o
Communication RS232, Modbus RS485
Web server Ethernet 10 BaseT/RS232 MODEM, TCP / IP
Weight 24V: 10.7 kg, 230V PSU: 14.5 kg
Humidity 0 - 95 %
Ordering Information
FHSD7215D 15 Channel Micro bore aspirated early warning smoke detection system
FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215FHSD720RL Relay Module 4 Channel for FHSD72x
FHSD731 Conversion kit for remote display
FHSD732 Single channel remote disp lay & programmer
FHSD733 Remote display repeate r un it - 16 un its
FHSD752 Filter in-line single stage
FHSD753 Filter in-line 3 stage
FHSD755 Replacement filter element set - medium / fine for the FHSD753
FHSD756 Replacement filter element pack of 10 - coarse - for the FHSD753
FHSD761 Micro bore 6mm sampling tube - 30 meter ree l
FHSD762 Straight union fo r micro bore 6mm tube
FHSD763 Tee union for micro bore 6mm tube
FHSD764 Scintered end of l ine f il ter for micro bore 6mm tube
Early warning applications
Detection with high airflows
Unobtrusive detection
Ideal for large open areas
For inaccessible areas
For dusty and humid environments
For tamperproof installations
Micro bore pipes
15 Channel Micro bore aspirated early warning smoke detection system FHSD7215D
8/10/2019 Catalog Accesorii Incendiu
11/105
Page 10
Aspiration Systems
A 230V power supply, battery charger and battery container for the FHSD721,FHSD724, FHSD726, and FHSD7215 apiration systems. The power supply is
easily mounted in the units.
Ordering Information
FHSD720PS PSU Batt charger 230V for FHSD721-FHSD7215
PSU Batt charger 230V for FHSD721-FHSD7215 FHSD720PS
This four way relay module extends the outputs of the FHSD72x aspiration
systems. It is plug-in installable.
Ordering Information
FHSD720RL Relay Module 4 Channel for FHSD72x
Relay Module 4 Channel for FHSD72x FHSD720RL
8/10/2019 Catalog Accesorii Incendiu
12/105
Page 11
Aspiration Systems
This kit allows the display panel of a FHSD72xD aspiration system to beremoved from the unit and to be mounted remotely.
Ordering Information
FHSD731 Conversion kit for remote display
Conversion kit for remote display FHSD731
Ordering Information
FHSD732 Single channel remote disp lay & programmer
Single channel remote display & programmer FHSD732
8/10/2019 Catalog Accesorii Incendiu
13/105
Page 12
Aspiration Systems
A remote display channel allowing the connection of up to16 aspirationsystems on a RS485 bus.
Ordering Information
FHSD733 Remote display repeate r un it - 16 un its
Remote display repeater unit - 16 units FHSD733
For use with large bore systems
Ordering Information
FHSD751 Filter+ with fi lter element - harsh environment
Filter+ with filter element - harsh environment FHSD751
8/10/2019 Catalog Accesorii Incendiu
14/105
Page 13
Aspiration Systems
A single stage filter for micro-bore systems
Ordering Information
FHSD752 Filter in-line single stage
Filter in-line single stage FHSD752
A three stage filter with course, medium, and fine filters for micro-bore
systems
Ordering Information
FHSD753 Filter in-line 3 stage
Filter in-line 3 stage FHSD753
8/10/2019 Catalog Accesorii Incendiu
15/105
Page 14
Aspiration Systems
Ordering Information
FHSD754 Rep lacement f il te r e lement for the FHSD751
Replacement filter element for the FHSD751 FHSD754
Ordering Information
FHSD755 Replacement filter element set - medium / fine for the FHSD753
Replacement filter element set - medium / fine for the FHSD753 FHSD755
8/10/2019 Catalog Accesorii Incendiu
16/105
Page 15
Aspiration Systems
Ordering Information
FHSD756 Replacement filter element pack of 10 - coarse - for the FHSD753
Replacement filter element pack of 10 - coarse - for the FHSD753 FHSD756
Ordering Information
FHSD761 Micro bore 6mm sampling tube - 30 meter ree l
Micro bore 6mm sampling tube - 30 meter reel FHSD761
8/10/2019 Catalog Accesorii Incendiu
17/105
8/10/2019 Catalog Accesorii Incendiu
18/105
Page 17
Aspiration Systems
Ordering Information
FHSD764 Scintered end of l ine f il ter for micro bore 6mm tube
Scintered end of line filter for micro bore 6mm tube FHSD764
Ordering Information
FHSD771 Large bore red pipe 3 metre length
Large bore red pipe 3 metre length FHSD771
8/10/2019 Catalog Accesorii Incendiu
19/105
Page 18
Aspiration Systems
Ordering Information
FHSD772 Straight union large bore
Straight union large bore FHSD772
Ordering Information
FHSD773 90 deg. bend for large bore pipes
90 deg. bend for large bore pipes FHSD773
8/10/2019 Catalog Accesorii Incendiu
20/105
Page 19
Aspiration Systems
Ordering Information
FHSD774 45 deg. elbow for large bore pipes
45 deg. elbow for large bore pipes FHSD774
Ordering Information
FHSD775 End cap for large bore pipes
End cap for large bore pipes FHSD775
8/10/2019 Catalog Accesorii Incendiu
21/105
FLAME DETECTORS
8/10/2019 Catalog Accesorii Incendiu
22/105
Page 21
Flame Detectors
Technical Data
Supply Voltage 12 - 30 V dc
Supply current 3 mA quiescent
Relay contact ratings 1A @ 30 V dc (resistive load)
Field of view Up to 120
Spectral response (UV) 185 to 260 nm
Operating temperature -10C - 60C
Relative Humidity 95% Non condensing
Weight 150 g (including base)
Ordering Information
FF711 UV f lame detec tor complete w ith s tandard 2 wi re base
FF711R 24 V dc relay base for FF 711
UV, IR and UV/IR models
Low cost units for indoor applications
Flame proof model available
Fast response (1 - 2 seconds)
Wide operating voltage
Wide cone of vision - up to 120
2 Wire and relay operation
Versatile, adjustable test torch available
Universal mounting bracket
UV flame detector complete with standard 2 wire base FF711
8/10/2019 Catalog Accesorii Incendiu
23/105
Page 22
Flame Detectors
Technical Data
Supply Voltage 12 - 30 V dc
Supply current 4 mA
Relay contact ratings 1A @ 30 V dc (resistive load)
Field of view Up to 120
Spectral response (UV) 185 to 260 nm
Operating temperature -10C - 60C
Relative Humidity 95% Non condensing
Weight 655 g
Ordering Information
FF713 UV f lame detec tor sel f contained wi th fi re and faul t relays
UV, IR and UV/IR models
Low cost units for indoor applications
Flame proof model available
Fast response (1 - 2 seconds)
Wide operating voltage
Wide cone of vision - up to 120
2 Wire and relay operation
Versatile, adjustable test torch available
Universal mounting bracket
UV flame detector self contained with fire and fault relays FF713
8/10/2019 Catalog Accesorii Incendiu
24/105
Page 23
Flame Detectors
Technical Data
Supply Voltage 12 - 30 V dc
Supply current 3 mA quiescent
Relay contact ratings 1A @ 30 V dc (resistive load)
Field of view Up to 120
Spectral response (UV) 185 to 260 nm
Operating temperature -10C - 60C
Relative Humidity 95% Non condensing
Weight 2.2 kg
Ordering Information
FF716 UV f lame detec tor with f ire relay in flame proo f enclosure
UV, IR and UV/IR models
Low cost units for indoor applications
Flame proof model available
Fast response (1 - 2 seconds)
Wide operating voltage
Wide cone of vision - up to 120
2 Wire and relay operation
Versatile, adjustable test torch available
Universal mounting bracket
UV flame detector with fire relay in flame proof enclosure FF716
8/10/2019 Catalog Accesorii Incendiu
25/105
Page 24
Flame Detectors
Technical Data
Supply Voltage 17 - 30 V dc
Supply current 67A
Relay contact ratings 1A @ 30 V dc (resistive load)
Field of view 100
Spectral response (IR) Near 4.3um
Operating temperature -10C - 60C
Relative Humidity 95% Non condensing
Weight -
Ordering Information
FF721 IR flame detector complete with 2 wire base
UV, IR and UV/IR models
Low cost units for indoor applications
Flame proof model available
Fast response (1 - 2 seconds)
Wide operating voltage
Wide cone of vision - up to 120
2 Wire and relay operation
Versatile, adjustable test torch available
Universal mounting bracket
IR flame detector complete with 2 wire base FF721
8/10/2019 Catalog Accesorii Incendiu
26/105
Page 25
Flame Detectors
Technical Data
Supply voltage 14 - 28 V dc
Supply current 3/9, 4/8/14, 4-20, 8-20 mA
Relay contact ratings 1 A @ 30 V dc (resistive load)
Field of view 90 min. cone
Spectral response (IR) 1.0 to 2 m
Operating temperature -10C to 55C
Storage temperature -20C to 65C
Relative humidity 95%; non-condensing
IP Rating IP64 poly carbonate box
IP65 die-cast zinc alloy boxIP66 flame proof box
Weight 1 kg die-cast zinc ally box
2 kg flame proof box
Ordering Information
FF741 Dual IR f lame detector in glass reinforced polycarbonate housing
FF742 Dual IR flame detecto r in d ie-cast zinc al loy housing
FF746 Dual IR flame detecto r in Eexd - I IC T6 flame proof housing
FF747 Dual IR Intrinsic safe flame detector in die-cast z inc alloy housing
Dual IR and UV/Dual IR models
High specification units for critical applications
IP65 Housing available
Flame proof and Intrinsic safe models
Low current consumption
2 Wire, 4 - 20 mA and relay operation
Latching and non latching operation
High / Low sensitivity setting
Versatile mounting brackets
Tolerance to detector window contamination
Versatile, adjustable test torch available
Remote self test facility
Microprocessor controlled
Immunity to false sources (arc welding, lightning and static)
Conforms to EN54: Part 10
Dual IR flame detector in glass reinforced polycarbonate housing FF741
8/10/2019 Catalog Accesorii Incendiu
27/105
Page 26
Flame Detectors
Technical Data
Supply voltage 14 - 28 V dc
Supply current 3/9, 4/8/14, 4-20, 8-20 mA
Relay contact ratings 1 A @ 30 V dc (resistive load)
Field of view 90 min. cone
Spectral response (IR) 1.0 to 2 m
Operating temperature -10C to 55C
Storage temperature -20C to 65C
Relative humidity 95%; non-condensing
IP Rating IP64 poly carbonate box
IP65 die-cast zinc alloy boxIP66 flame proof box
Weight 1 kg die-cast zinc ally box
2 kg flame proof box
Ordering Information
FF751 UV / Dua l IR f lame detec tor in die cast zinc al lo y housing
FF756 UV / Dual IR f lame detector in Eexd - I IC T6 f lame proof housing Dual IR and UV/Dual IR models
High specification units for critical applications
IP65 Housing available
Flame proof and Intrinsic safe models
Low current consumption
2 Wire, 4 - 20 mA and relay operation
Latching and non latching operation
High / Low sensitivity setting
Versatile mounting brackets
Tolerance to detector window contamination
Versatile, adjustable test torch available
Remote self test facility
Microprocessor controlled
Immunity to false sources (arc welding, lightning and static)
Conforms to EN54: Part 10
UV / Dual IR flame detector in die cast zinc alloy housing FF751
8/10/2019 Catalog Accesorii Incendiu
28/105
Page 27
Flame Detectors
A microproccessor universal test torch that can test all FF700 series flamedetectors. It emits various channels of infra-red to test dual IR detectors. It
also can emit 'flickering' IR to test for false alarms.
Ordering Information
FF703 UV/IR universal test torch
UV/IR universal test torch FF703
A universal swivel mounting bracket for most FF700 flame detectors.
Ordering Information
FF705 Adjustable mounting bracket
Adjustable mounting bracket FF705
8/10/2019 Catalog Accesorii Incendiu
29/105
Page 28
Flame Detectors
A weather shield that can be used for most FF700 flame detectors
Ordering Information
FF706 Stainless steel weather shield
Stainless steel weather shield FF706
8/10/2019 Catalog Accesorii Incendiu
30/105
BEAM DETECTORS
8/10/2019 Catalog Accesorii Incendiu
31/105
Page 30
Beam Detectors
Technical Data
Supply Voltage 11.5 - 28 VDC
Current consumption
Quiscent less than 13 mA
Alarm less than 20 mA
Operating Temperature -20 to 55 C
Size
Control Unit 210 x 160 x 80 mm
Heads 83 x 115 x 135 mm
IP Rating
Control Unit IP 50Heads IP 50
Construction
Control Unit Double pressed steel sheet
Heads Zinc alloy
Colour
Control Unit White RAL 9010
Heads White RAL 9010
Certification VdS
Ordering Information
FD2000 Beam smoke detector
FD2010 Beam smoke detector flame proof
Large area coverage up to 1500 m per unit
Range from 10 to 100m
Up to ceiling heights of 25 m
12 to 24 VDC
Low current consumption
Manual or automatic reset
3 selectable alarm thresholds
Self check and automatic signal compensation
Automatic discrimination between fire and fault
Retro operation through prisms
Ground level electronics
Easy wiring and alignment
Conforms to BS5839 part 5
VdS approved
Atex explosion-proof version
Beam smoke detector FD2000
8/10/2019 Catalog Accesorii Incendiu
32/105
Page 31
Beam detectors
Technical Data
Supply voltage 10.2 - 30 V dc
Range
FD 705R 5 - 50 m
FD 710R 50 - 100 m
Lateral detection 7.5 m
Current consumption
Quiescent < 4 mA
Alarm < 15 mA
Optical wave length 880 nm
Operating temperature -30C to 55CSize 210 x 130 x 120 mm
IP rating IP50
Construction Flame retardent ABS
Colour Gray-black
Ordering Information
FD705R Reflective beam smoke detector 5 - 50m
FD710R Ref lec tive beam smoke detecto r; 50 - 100 m
Area coverage up to 600 m 2 per unit
Range from 5 - 50 m and 50 - 100 m
Up to ceiling heights of 25 m
10 to 30 V dc operation
Low current consumption
Manual or automatic reset
3 selectable alarm thresholds
Self check and automatic contamination compensation
Automatic discrimination between fire and fault
Retro operation through prism
Vertical or horizontal mount
Easy wiring and unique alignment
Microprocessor controlled
Conforms to BS 5839 part 5, EN54,VdS and UL
Reflective beam smoke detector 5 - 50m FD705R
8/10/2019 Catalog Accesorii Incendiu
33/105
LINEAR HEAT DETECTION
8/10/2019 Catalog Accesorii Incendiu
34/105
Page 33
Linear Heat Detection
Technical Data
Operating voltage range Volt dc 18-30
Operating current (typical) mA
Quiescent 28
Alarm 58
Operating temperature C -25 to +50
Relay contact rating (fire and fault) 1 A @ 30 V dc
IP rating IP65
Dimension (H x Wx D in mm) 80 x 80 x 52
Colour Grey, RAL 9002
Ordering Information
DT650L Conventional control ler for analogue linear heat cable
Conventional and analogue addressable controllers
Monitoring at the point of risk
Choice of temperatures
Ease of installation
Reliable and durable
Intrinsic safe solutions
Ideal for smoke less fires - overheating cables
VdS approved
Conventional controller for analogue linear heat cable DT650L
Technical Data
Operating voltage range Volt dc 18-30Operating current (typical) mA
Quiescent 2
Alarm 3.2
Operating temperature C -25 to +50
Relay contact rating (fire and fault) -
IP rating IP65
Dimension (H x Wx D in mm) 105 x 105 x 65
Colour Grey, RAL 9002
Ordering Information
DT950L 950 series addressable control ler for analogue linear heat cable
Conventional and analogue addressable controllers Monitoring at the point of risk
Choice of temperatures
Ease of installation
Reliable and durable
Intrinsic safe solutions
Ideal for smoke less fires - overheating cables
VdS approved
950 series addressable controller for analogue linear heat cable DT950L
8/10/2019 Catalog Accesorii Incendiu
35/105
Page 34
Linear Heat Detection
Technical Data
1m alarm temp C 70-125
10m alarm temp C 45-100
Operating temp C -20 to +70
Outer sheath material Red PVC
Dimensions (diameter in mm) 2.8
Ordering Information
HC650 Analogue linear heat cable PVC 500 meter
DT650L Conventional control ler for analogue linear heat cable
Analogue linear heat cable
Conventional and analogue addressable controllers
Monitoring at the point of risk
Ease of installation
Reliable and durable
Ideal for smoke less fires - overheating cables
VdS approved with DT650L & DT950L controllers
Analogue linear heat cable PVC 500 meter HC650
8/10/2019 Catalog Accesorii Incendiu
36/105
Page 35
Linear Heat Detection
The Rilsan coating gives a high resistance to chemical substances
Technical Data
1m alarm temp C 70-125
10m alarm temp C 45-100
Operating temp C -20 to +70
Outer sheath material Rilsan coated
Dimensions (diameter in mm) 4
Ordering Information
HC650R Analogue l inear heat cable with Rilsan coating 500 meter
DT650L Conventional control ler for analogue linear heat cableDT950L 950 series addressable control ler for analogue linear heat cable
Analogue linear heat cable
Conventional and analogue addressable controllers
Monitoring at the point of risk
Ease of installation
Reliable and durable
Ideal for smoke less fires - overheating cables
VdS approved with DT650L & DT950L controllers
Analogue linear heat cable with Rilsan coating 500 meter HC650R
8/10/2019 Catalog Accesorii Incendiu
37/105
Page 36
Linear Heat Detection
The stainless steel coating gives high mechanical strength.
Technical Data
1m alarm temp C 70-125
10m alarm temp C 45-100
Operating temp C -20 to +70
Outer sheath material Stainless steel
Dimensions (diameter in mm) 3.5
Ordering Information
HC650S Analogue linear heat cable with stainless steel covering - 500 meter
DT650L Conventional control ler for analogue linear heat cable
DT950L 950 series addressable control ler for analogue linear heat cable
Analogue linear heat cable
Conventional and analogue addressable controllers
Monitoring at the point of risk
Ease of installation
Reliable and durable
Ideal for smoke less fires - overheating cables
VdS approved with DT650L & DT950L controllers
Analogue linear heat cable with stainless steel covering - 500 meter HC650S
The Rilsan and stainless steel covering gives mechanical strength and
chemical resistance
Technical Data
1m alarm temp C 70-125
10m alarm temp C 45-100
Operating temp C -20 to +70
Outer sheath material Rilsan and Stainless steel
Dimensions (diameter in mm) 4.5
Ordering Information
HC650RS Analogue linear heat cable - Rilsan and stainless steel cover - 500 m
DT650L Conventional control ler for analogue linear heat cable
DT950L 950 series addressable control ler for analogue linear heat cable
Analogue linear heat cable Conventional and analogue addressable controllers
Monitoring at the point of risk
Ease of installation
Reliable and durable
Ideal for smoke less fires - overheating cables
VdS approved with DT650L & DT950L controllers
Analogue linear heat cable - Rilsan and stainless steel cover - 500 meter HC650RS
8/10/2019 Catalog Accesorii Incendiu
38/105
Page 37
Linear Heat Detection
A range of digital heat senging cable from 68C to 235C
Technical Data
Max operating voltage 100 V ac/dc
Conductor resistance 100 Ohm/km
Alarm temp C 68
Max ambient C 45
Outer sheath material Polythene Braid
Colour/Marking Red/Green tracer
Dimensions (diameter in mm) 3.65
Ordering Information
HCD607 Dig ita l heat sens ing cab le 68C - 500 meter
HCD609 Dig ita l heat sens ing cab le 88C 500 meter
HCD610 Dig ita l heat sens ing cab le 105C 500 meter
HCD618 Dig ita l heat sens ing cab le 180C 500 meter
HCD623 Dig ita l heat sens ing cab le 235C 500 meter
Digital linear heat cable
Monitoring at the point of risk
Choice of temperatures
Ease of installation
Reliable and durable
Intrinsic safe solutions
Ideal for smoke less fires - overheating cables
Digital heat sensing cable 68C - 500 meter HCD607
8/10/2019 Catalog Accesorii Incendiu
39/105
Page 38
Linear Heat Detection
Ordering Information
HCA601 A clip for heat cable 100/pack
'A' clip for heat cable 100/pack HCA601
Ordering Information
HCA602 P clip for heat cable 100/pack
'P' clip for heat cable 100/pack HCA602
8/10/2019 Catalog Accesorii Incendiu
40/105
Page 39
Linear Heat Detection
Ordering Information
HCA603 T clip for heat cable 100/pack
T' clip for heat cable 100/pack HCA603
HCA 605-x
A range of edge clips to fit on structures from 2 to 20 mm
Ordering Information
HCA605-3 Edge clip for heat cable 2-3 mm 100/pack
HCA605-8 Edge clip for heat cable 3-8 mm 100/pack
HCA605-14 Edge cl ip for heat cable 8-14mm 100/pack
HCA605-20 Edge clip for heat cable 14-20mm 100/pack
Edge clip for heat cable 2-3 mm 100/pack HCA605-3
8/10/2019 Catalog Accesorii Incendiu
41/105
CO DETECTION
8/10/2019 Catalog Accesorii Incendiu
42/105
Page 41
CO Detection
The KM-Series CO detection system is designed for applications such as
vehicle parking areas where concentrations of CO may accumulate. The range
is compliant with the UNE23.300/84 standard. The KM260/1 is a 1 to 5 zonescontrol unit, using KM170 detectors.
Technical Data
Power Supply
Mains Supply 230 VAC 10% 50 Hz
Power Consumption 95 W (max)
Zone Configuration
Zone Input Voltage 10-20 VDC/VAC
Sensitiviy 0-300 ppm
Cable Requirement 3 core 1.5 mm
Cable Length (max) 350 m
No. of Detectors (max) 15
No. of Zones (max) 5
MechanicalHousing (w x h x d) 275 x 335 x 130 mm
Weight 6 kg
Ordering Information
KM260/1-ING CO detection control panel - 1 Zone
KM260/2-ING CO detection control panel - 2 Zones
KM260/3-ING CO detection control panel - 3 Zones
KM260/4-ING CO detection control panel - 4 Zones
KM260/5-ING CO detection control panel - 5 Zones
Designed according to norm 23300/84
Miner CDM8001 and CDM8002 standard password
LGAI 154.909 and 96013132 standard certification
Easy to use
Low current consumption
Direct reading of measured levels
Easy installation
Extraction relays and alarm outputs per area
From 1 to 5 areas
3-wire system
Modular design
Up to 15 detectors per zone
10 seconds response time
Elegant design
Supervision of all zone lines
Available in various languages
CO detection control panel - 1 Zone KM260/1-ING
CO detection control panel - 2 Zones KM260/2-ING
CO detection control panel - 3 Zones KM260/3-ING
CO detection control panel - 4 Zones KM260/4-ING
CO detection control panel - 5 Zones KM260/5-ING
8/10/2019 Catalog Accesorii Incendiu
43/105
Page 42
Expansion Module
The KM260 is an expansion module for the KM260-Series CO panels from GE-Interlogix. It allows for an additional monitoring zone to be added to the
control panel, each module allowing for an additional 15 sensors to be
connected.
Technical Data
Power Supply
Mains Supply 230 VAC 10% 50 Hz
Power Consumption 95 W (max)
Zone Configuration
Zone Input Voltage 10-20 VDC/VAC
Sensitiviy 0-300 ppm
Cable Requirement 3 core 1.5 mm
Cable Length (max) 350 m
No. of Detectors (max) 15No. of Zones (max) 1
Ordering Information
KM260-ING CO detection expansion module (English Version)
Designed according to norm 23300/84
Miner CDM8001 and CDM8002 standard password
LGAI 154.909 and 96013132 standard certification
Easy to use
Low current consumption
Direct reading of measured levels
Easy installation
Extraction relays and alarm outputs per area
3-wire system
Up to 15 detectors per zone
10 seconds response time
Supervision of zone line
Available in various languages
CO detection expansion module (English Version) KM260-ING
8/10/2019 Catalog Accesorii Incendiu
44/105
Page 43
Detectors
The KM170 detector is specifically designed to react to the presence of carbonmonoxide. The design complies with the requirements of the UNE 23-300
standard.
Technical Data
Sensor Type TGS Semicondictor
Useful Life 4 years
Electrical Characteristics
Supply Voltage 10 to 20 VDC
Quiescent Current 35 mA
Reaction Time 10 s
Environmental
Operating Temperature 0 to 40 C
Protection Index IP205
MechanicalSize (h x ) 81 x 109 mm
Weight 115 g
Material and Colour ABS White
Installation
Number of detectors per zone 15
Covarage 300 m
Ordering Information
KM170 CO detector wi th base and mount ing supplement
Complies with the requirements of the UNE23-300 standard
Microprocessor based
Resolution of up to 5 ppm
Response time of 10 s
Low current consumption
Local status indication of:
- Normal operation
- 50 ppm detected
- Fault
Useful life of up to 4 years
CO detector with base and mounting supplement KM170
8/10/2019 Catalog Accesorii Incendiu
45/105
MANUAL CALL POINTS
8/10/2019 Catalog Accesorii Incendiu
46/105
Page 45
Manual Call Points
DM700 Series
A range of call points with flying leads that can but flush mounted or surface
mounted using a back-box
Technical Data
Material Self-extinguishing Noryl SE100
Max. contact rate resistive load
50 V ac or 30 V dc 8 A
50 V dc 3 A
Contact resistance Max. 50 milliohm
Series resistor -
Colour Red - RAL N3020
Operating temperature -40 to +85C
Relative humidity max. 90% RV
Ordering Information
DM700 Manual callpoint, flying leads
DM700B Manual callpoint, flying leads, blue
DM700R Manual callpoint, f ly ing leads, 470 Ohm series resistor
DM700RB Manual callpoint, flying leads, 470 Ohm series resistor, blue
DM700L Manual callpoint, flying leads, 470 Ohm series resistor & LED
DM700LB Manual callpoint, flying leads, 470 Ohm series resistor & LED, blue
DM700G Manual ca llpoin t, fl ying leads , green
DM711 Glass, EN54, Aritech
DM715 Glass, EN54, Universal
Easy to install
With or without series resistor
With or without LED
With breakglass or resettable
Easy to replace glass
Surface and flush mounting options
High quality micro switch
Glass protected with foil
Standard EN54 symbol
Standard accepts hinged cover
Key test facility
Manual callpoint, flying leads DM700
8/10/2019 Catalog Accesorii Incendiu
47/105
Page 46
Manual Call Points
Technical Data
Material - standard Self-extinguishing Noryl SE 100
Max. contact rate resistive load
50 V ac or 30 V dc 8.0 A
50 V dc 3.0 A
Contact resistance Max. 50 milliohms
Standard colour Red - RAL N 3020
Ambient temperature range -40 to + 85 C
Maximum relative humidity 90% RV
Ordering Information
DM700E Surface mount manual callpoint IP67, including blackbox
DM700E
Easy to install
With breakglass or resettable
Easy to replace glass
High quality micro switch
IP67
EN54 approved
Surface mount manual callpoint IP67, including blackbox DM700E
8/10/2019 Catalog Accesorii Incendiu
48/105
Page 47
Manual Call Points
Technical Data
Material - standard Glass reinforced polycarbonate
Contact resistance Max. 50 milliohms
Standard colour Red - RAL N 3020
Ambient temperature range -55 to + 55 C
Maximum relative humidity 90% RV
Ordering Information
DM700IS Surface mount IP 66/67 intrinsic safe MCP, including back box
Easy to install
With breakglass or resettable
Easy to replace glass
Surface and flush mounting options
High quality micro switch
Glass protected with foil
ATEX approved
Preformed mounting slots
Key test facility
Surface mount IP 66/67 intrinsic safe MCP, including back box DM700IS
8/10/2019 Catalog Accesorii Incendiu
49/105
Page 48
Manual Call Points
DM700 Series
Technical Data
Material Self-extinguishing Noryl SE100
Max. contact rate resistive load
50 V ac or 30 V dc 8 A
50 V dc 3 A
Contact resistance Max. 50 milliohm
Series resistor -
Colour Red - RAL N3020
Operating temperature -40 to +85C
Relative humidity Max. 90% RV
Ordering Information
DM700K Manual ca llpoin t wi th keyswitch, fl ying leads
DM700KB Manual callpoint with keyswitch, flying leads, blue Easy to install
Surface and flush mounting options
High quality key switch
Operates after long period of disuse
Standard EN54 symbol
Preformed mounting slots
Manual callpoint with keyswitch, flying leads DM700K
8/10/2019 Catalog Accesorii Incendiu
50/105
Page 49
Manual Call Points
A standard EN54 glass for DM700 series of call points, with Aritech logo
Ordering Information
DM711 Glass, EN54, Aritech
Glass, EN54, Aritech DM711
A universal EN54 approved glass for the DM700 series of detectors, no logo
Ordering Information
DM715 Glass, EN54, Universal
Glass, EN54, Universal DM715
A hinged transparent cover to protect accidental operation of DM700 series
manual call points
Ordering Information
DM782 Hinged transparent MCP protection cover
Unobtrusive
Transparent
Protects from accidental alarm activation
Hinged transparent MCP protection cover DM782
8/10/2019 Catalog Accesorii Incendiu
51/105
Page 50
Manual Call Points
A back box for the surface mounting of DM700 call points, without connectors
Ordering Information
DM788 Surface mount box without connectors
DM788Y Sur face mount box wi thout connectors, ye ll ow
DM788B Sur face mount box wi thout connectors, blue
Surface mount box without connectors DM788
A surface mount box with three connectors for DM700 series manual callpoints.
Ordering Information
DM787 Surface mounting box with connectors
DM787Y Sur face mounting box wi th connectors, ye ll ow
DM787B Sur face mounting box wi th connectors, blue
DM787G Sur face mounting box wi th connectors, green
Surface mount back box for MCP - RED
Surface mounting box with connectors DM787
8/10/2019 Catalog Accesorii Incendiu
52/105
Page 51
Manual Call Points
General
The PK20 manual call point is a manual alarm activation point for
conventional detection systems. Once activated, it remains activated until it
is manually reset using a key. To reset, simply turn the key a turn to the
right and it is ready for use.
This call point has been designed for indoor use.
Technical Data
Size 100 x 95 x 43 mm
Max. recommended distance between units 60 m
Installation height 1.2 - 1.5mFastening screws 2x (3.5 x 30 mm)
Power supply voltage 24 VDC
Consumption in standby 0 mA
Consumption in alarm 60 mA
Status Indications Standby, Alarm
Working temperature -10 to 50C
Storage temp. -10 to 50C
Max. relative humidity 95%
Ordering Information
PK20 Resetable Manual Call Point
PK20M Flush mount cradle
PK20T Hinged transparent MCP protection cover
Standard labelling (pictograms)
Spare crystals not required
Easy installation
Easy maintenance
Accessory for flush mount (optional)
Transparent protection cover (optional)
For conventional systems
Modern, robust and elegant design
Resetable Manual Call Point PK20
Accessory for PK20 restable manual callpoint. This cradle allows for the PK20
to be flush mounted.
Ordering Information
PK20M Flush mount cradle
Allows flush mounting of the PK20 manual call point
Flush mount cradle PK20M
8/10/2019 Catalog Accesorii Incendiu
53/105
Page 52
Manual Call Points
Accesory for PM20 resetable manual callpoint. Made of transparent plasic, itprevents the manual call point from being accidentally activated.
Ordering Information
PK20T Hinged transparent MCP protection cover
Unobtrusive
Transparent
Protects from accidental alarm activation
Hinged transparent MCP protection cover PK20T
8/10/2019 Catalog Accesorii Incendiu
54/105
FIRE INDICATORS
8/10/2019 Catalog Accesorii Incendiu
55/105
Page 54
Fire indicators
This low current remote indicator can be used with all 650, 950, 700 & 2000series detectors, and can also be used in intrinsic safe applications.
Ordering Information
AI671 Mini disc remote indicator
Mini disc remote indicator AI671
8/10/2019 Catalog Accesorii Incendiu
56/105
Page 55
Fire indicators
Technical Data
Material Self-extinguishing polycarbonate
Dimensions (L x W x H) 80 x 80 x30 mm
Colour White RAL 9010
Operating voltage 12-28 V dc
Current consumption 4 mA nominal
Flashing frequency 1.3 Hz
Light intensity 200 mcd
Colour LEDs RED
Ordering Information
AI672 Optical Remote Indicator
Wide operating voltage
Low current consumption
Universal mounting plate
Low profile
Clearly visible, large LEDs
Protected against polarity reversal
Connects up to 4 detectors
Blinking or fixed LEDs
High sound output
With and without sounder
Optical Remote Indicator AI672
Technical Data
Material Self-extinguishing polycarbonate
Dimensions (L x W x H) 80 x 80 x 30 mm
Weight 55 g
Colour White RAL N 9010
Surface Textured
Terminals 5
Operating Voltage 12 - 28 V dc
Current consumption 4 mA nominal
Flashing frequency 1.3 Hz
Light intensity 200 mcd
Colour LEDs Red
Sound pressure 81 dBA 1 metreFrequency 3600 Hz
Ordering Information
AI673 Optical and Accustical Remote Indicator
Wide operating voltage
Low current consumption
Universal mounting plate
Low profile
Clearly visible, large LEDs
Protected against polarity reversal
Connects up to 4 detectors
Blinking or fixed LEDs
High sound output
With and without sounder
Optical and Accustical Remote Indicator AI673
8/10/2019 Catalog Accesorii Incendiu
57/105
Page 56
Fire indicators
Technical Data
Electrical Specifications
Supply Voltage 18 to 27 VDC
Activation Voltage 18 to 27 VDC
Current Consumption 600 mA
Switching Polarity NA
Indicators 24 V 3 W
Environmental Specifications
Working Temperature -10 to 75 C
Physical Specifications
Number of zones NA
Buzzer output 80 dB
Housing Colour Grey
Display Colour RedWeight 700 g
Ordering Information
KR24 Illuminated extinguishing waring sign (Spanish version) 24VDC
KR Repeaters
- Zone indication with alarm buzzer
- Local buzzer silence control
- Local buzzer silenced indication
- Alarm indicated until removed
KR Signs
- Low current consumption
- Large angle of view
- Optical and acoustic indications selectable
- Modern and elegant design
Illuminated extinguishing waring sign (Spanish version) 24VDC KR24
8/10/2019 Catalog Accesorii Incendiu
58/105
Page 57
Fire indicators
The KR24 is specifically designed as an evacuation warning sign for gas
extinguising areas. The KR24B has no text on the backlit display, and text may
therefor be added as required for the application. Units supplied with text in
various languages are also availble.
Technical Data
Electrical Specifications
Supply Voltage 18 to 27 VDC
Activation Voltage 18 to 27 VDC
Current Consumption 600 mA
Switching Polarity NA
Indicators 24 V 3 W
Environmental Specifications
Working Temperature -10 to 75 C
Physical Specifications
Number of zones NA
Buzzer output 80 dB
Housing Colour Grey
Display Colour Red
Weight 700 g
Ordering Information
KR24B Illuminated warning sign (No text) 24VDC
- Low current consumption
- Large angle of view
- Optical and acoustic indications selectable
- Modern and elegant design
Illuminated warning sign (No text) 24VDC KR24B
The KR24 is specifically designed as an evacuation warning sign for gasextinguising areas. The KR24B has no text on the backlit display, and text may
therefor be added as required for the application. Units supplied with text in
various languages are also availble.
Technical Data
Electrical Specifications
Supply Voltage 18 to 27 VDC
Activation Voltage 18 to 27 VDC
Current Consumption 600 mA
Switching Polarity NA
Indicators 24 V 3 W
Environmental Specifications
Working Temperature -10 to 75 C
Physical Specifications
Number of zones NA
Buzzer output 80 dB
Housing Colour Grey
Display Colour Red
Weight 700 g
Ordering Information
KR24B Illuminated warning sign (No text) 24VDC
- Low current consumption
- Large angle of view
- Optical and acoustic indications selectable
- Modern and elegant design
Illuminated warning sign (No text) 24VDC KR24B
8/10/2019 Catalog Accesorii Incendiu
59/105
Page 58
Fire indicators
The PA25 series remote indicators have been designed for direct connection tofire detectors, enabling luminous indication outside the area where the
detector is installed.
Technical Data
Electrical Specifications
Supply Voltage (Analogue Systems)5 to 10 VDC
Supply Voltage (Conventional Systems) 2 to 5 VDC
Current Consumption < 50 mA
Mechanical Specifications
Size (w x h x d) 80 x 80 x 42 mm
Weight 10 g
Box material A.B.S.
Colour White
Environmental SpecificationsProtection level IP20
Working temperature -10 to +60 C
Storage temperature -10 to +70 C
Ordering Information
PA25/3L Low current remote LED indicator Direct two-wire connection to detector
Large angle of visibility - lit up on four sides
Low current consumption
Flashing option
2 to 28 VDC power supply (depending on model)
High luminosity
Compatible with third party products
IP20 protection level
Modern and elegant design
ABS plastic casing with ruby red polycarbonate spy-hole
Shock resistant
Low current remote LED indicator PA25/3L
8/10/2019 Catalog Accesorii Incendiu
60/105
Page 59
Fire indicators
The PA25 series remote indicators have been designed for direct connection tofire detectors, enabling luminous indication outside the area where the
detector is installed.
Technical Data
Electrical Specifications
Supply Voltage (Analogue Systems)7 to 12 VDC
Supply Voltage (Conventional Systems) NA
Current Consumption 35 mA
Mechanical Specifications
Size (w x h x d) 80 x 80 x 42 mm
Weight 10 g
Box material A.B.S.
Colour White
Environmental SpecificationsProtection level IP20
Working temperature -10 to +60 C
Storage temperature -10 to +70 C
Ordering Information
PA25/9 Remote LED indicator 9 VDC Direct two-wire connection to detector
Large angle of visibility - lit up on four sides
Low current consumption
Flashing option
2 to 28 VDC power supply (depending on model)
High luminosity
Compatible with third party products
IP20 protection level
Modern and elegant design
ABS plastic casing with ruby red polycarbonate spy-hole
Shock resistant
Remote LED indicator 9 VDC PA25/9
8/10/2019 Catalog Accesorii Incendiu
61/105
Page 60
Fire indicators
The PA25 series remote indicators have been designed for direct connection tofire detectors, enabling luminous indication outside the area where the
detector is installed.
Technical Data
Electrical Specifications
Supply Voltage (Analogue Systems)20 to 28 VDC
Supply Voltage (Conventional Systems) NA
Current Consumption 40 mA
Mechanical Specifications
Size (w x h x d) 80 x 80 x 42 mm
Weight 10 g
Box material A.B.S.
Colour White
Environmental SpecificationsProtection level IP20
Working temperature -10 to +60 C
Storage temperature -10 to +70 C
Ordering Information
PA25/24 Remote LED indicator 24 VDC Direct two-wire connection to detector
Large angle of visibility - lit up on four sides
Low current consumption
Flashing option
2 to 28 VDC power supply (depending on model)
High luminosity
Compatible with third party products
IP20 protection level
Modern and elegant design
ABS plastic casing with ruby red polycarbonate spy-hole
Shock resistant
Remote LED indicator 24 VDC PA25/24
8/10/2019 Catalog Accesorii Incendiu
62/105
FIRE SOUNDERS & BEACONS
8/10/2019 Catalog Accesorii Incendiu
63/105
Page 62
Fire Sounders & Beacons
A compact high output, low current sounder ideal for hotels and hospitals.Available in panel mount, flange mount, and cover flange.
Ordering Information
AS262 Compact sounder
AS262FL Mini sounder, flange mount
AS262COF Mini sounder, cover flange mount
Low current consumption
High sound output
12 - 24 V dc and 230 Vac
Available in panel and flange mount
Compact sounder AS262
8/10/2019 Catalog Accesorii Incendiu
64/105
Page 63
Fire Sounders & Beacons
Technical Data
Operation Continuous
Supply voltage 10 - 28 V dc
Current consumption 7 mA
(see tone table in manual)
Number of tones 26
Starting current 30 mA, 2 msec
Automatic synchronisation Phased start
Line monitoring input Polarised input
Housing ABS plastic
Lens -Ingress protection IP 65
Operating temperature -25 to +80 C
Dimensions in mm ( x D)
Shallow base 93 x 75
Deep base 93 x 105
Ordering Information
AS263 Sounder, 26 tones - shallow base
AS263IS AS 263 intrinsically safe, weatherproof sounder
AS263WAT AS 263 , wh ite w ith ant i-tamper
AS263HIS High output in trinsic safe sounder
Low current consumption
High sound output
Multiple tones selection
12 - 24 V dc and 230 Vac
Automatic synchronisation
Suitable for multiple stage evacuation
Red and white colour body
IP 65 intrinsic safe and high output ; IP 66/67 intrinsic safeversions
Low profile version
Version with xenon flash
Red or clear lens for beacon
Sounder, 26 tones - shallow base AS263
8/10/2019 Catalog Accesorii Incendiu
65/105
Page 64
Fire Sounders & Beacons
Technical Data
Operation Continuous
Supply voltage 10 - 28 V dc
Current consumption 7 mA
(see tone table in manual) @ 240V
Number of tones 26
Starting current 30 mA 30 mA - 2 ms
Automatic synchronisation Phased start
Line monitoring input Polarised input
Housing ABS plastic
Ingress protection IP 65Operating temperature -25 to +80 C
Dimension ( x D)
Shallow base 93 x 75 mm
Deep base 93 x 105 mm
Ordering Information
AS264 Sounder, 26 tones - deep base
AS264M AS 264 mains powered 230 VAC
Low current consumption
High sound output
Multiple tones selection
12 - 24 V dc and 230 Vac
Automatic synchronisation
Suitable for multiple stage evacuation
Red and white colour body
IP 65 intrinsic safe and high output ; IP 66/67 intrinsic safeversions
Low profile version
Version with xenon flash
Red or clear lens for beacon
Sounder, 26 tones - deep base AS264
8/10/2019 Catalog Accesorii Incendiu
66/105
Page 65
Fire Sounders & Beacons
Technical Data
Operation Continuous
Supply voltage 18 - 30 V dc
Current consumption 68 mA
(see tone table in manual)
Number of tones 2
Starting current 30 mA - 10 ms
Automatic synchronisation Phased start
Line monitoring input Polarised input
Housing ABS plastic
Lens PolycarbonateIngress protection IP 65
Operating temperature -10C to +55 C
Dimensions in mm ( x D)
Shallow base 93 x 92
Deep base 93 x 121
Ordering Information
AS266 Combined sounder and beacon, 2 tones, red lens - shallow base
AS267 Combined sounder and beacon , 2 tones, red lens - deep base
Low current consumption
High sound output
Multiple tones selection
12 - 24 V dc and 230 Vac
Automatic synchronisation
Suitable for multiple stage evacuation
Red and white colour body
IP 65 intrinsic safe and high output ; IP 66/67 intrinsic safeversions
Low profile version
Version with xenon flash
Red or clear lens for beacon
Combined sounder and beacon, 2 tones, red lens - shallow base AS266
8/10/2019 Catalog Accesorii Incendiu
67/105
Page 66
Fire Sounders & Beacons
Technical Data
Operation Continuous
Supply voltage 9 - 30 V dc
Current consumption 3 mA
Number of tones 4
Starting current -
Automatic synchronisation Phased start
Line monitoring input Polarised input
Housing ABS plastic
Lens -
Ingress protection IP 42Operating temperature 25C to +85 C
Dimensions in mm ( x D) 101 x 25
Ordering Information
AS268 Sounder, 4 tones, low profile - low current
Low current consumption
High sound output
Automatic synchronisation
Suitable for multiple stage evacuation
Red and white colour body
Low profile version
Sounder, 4 tones, low profile - low current AS268
8/10/2019 Catalog Accesorii Incendiu
68/105
Page 67
Fire Sounders & Beacons
Technical Data
Operation Continuous
Supply voltage 12 - 30 V dc
Current consumption 5 mA
(see tone table in manual)
Number of tones 3
Starting current -
Automatic synchronisation Phased start
Line monitoring input Polarised input
Housing ABS plastic
Lens -Ingress protection IP 42
Operating temperature -25C to+70 C
Ordering Information
AS269 Sounder, 3 tones - low current, high output
Low current consumption
High sound output
Automatic synchronisation
Suitable for multiple stage evacuation
Red and white colour body
Sounder, 3 tones - low current, high output AS269
Ordering Information
AF310 Electronic solenoid bell, 24 VDC, red
Electronic solenoid bell, 24 VDC, red AF310
8/10/2019 Catalog Accesorii Incendiu
69/105
Page 68
Fire Sounders & Beacons
The SK06 cylindrical siren is available in various colours and is designed foruse inside buildings. Its compactness enables easy integration with building
interiors.
Tones are chosen by selection of micro switches. The siren clips onto a base
whereafter a saftey clip prevents unauthorised removal of the sounder from its
base. As an option, a deep base allows for cable entry and tubes up to a
diameter of 22 mm.
Technical Data
Electrical Characteristics
Supply Voltage 24 VDC
Current Consumption 12 to 17 mA
Environmental
Operating Temperature -40C + 70C
Ingress Protection IP45
Operational Parameters
Sounds ZC - FR - FL - SC
Sound Output 68 to 103 dBA
Colours Red, White, Cream
Ordering Information
SK06 Electronic alarm siren
Compact
Volume control
Up to 103 dB @ 1m
Very low current consumption
Easy assembly
Four different tones
No maintenance
Various colours
Bottom and sides cable entries
IP45
Electronic alarm siren SK06
8/10/2019 Catalog Accesorii Incendiu
70/105
Page 69
Fire Sounders & Beacons
The SK07 multi-tone siren is designed to sound an acoustic alarm signalinside buildings. This small, low profile siren combines a loud sound with low
power consumption. It complies with the requirements of the EN 54-3
standard.
Technical Data
Electrical
Supply Voltage 22 - 26 VDC
Alarm current 3 mA at 85 dBA or less than 20 mA at 95 dBA
Maximum sound level 95 dBA
Working temperature -20 C to 50 C
Storage temperature -20 C to 70 C
Maximum relative humidity 95 % (non condencing)
Mechanical
Dimensions 63 mm (h) x 93 mm Protection Index IP445
Fastening screws 2 x 30 mm
Maximum cable section 2.5 mm
Recommended cable s ize Sing le co re 1 .5 mm
Ordering Information
SK07 Low consumption multi-tone alarm siren
Low profile
Easy installation
Back and side cable entry
Polarity sensitive
Connection base included
Input and output terminals included
Acoustic power output selection
Up to 95 dBA sound output
Eight different alarm tones
Automatic tone change
Low current consumption
Low maintenance
IP445 protection level
EN54 part 3 compliant
Low consumption multi-tone alarm siren SK07
8/10/2019 Catalog Accesorii Incendiu
71/105
Page 70
Fire Sounders & Beacons
The SK20 is a general purpose sounder designed as part of a fire detectionsystem. For a fire system to fully comply with the provisions set forth in the
regulations for fire fighting installations, following the installation
recommendations of the UNE23-007-14 standard is advised.
Technical Data
Electrical Requirements
Supply voltage 9 to 30 VDC
Consumption @ 24 (tone dependant) 7 to 30 mA
Acoustic power output (tone dependant) 87 to 112 dBA
Nominal power of strobe 1 W
Environmental Specification
Working temperature -20 to +60 C
Storage temperature -20 to +70 C
Relative humidity < 95%Protection level IP445
Functional Specification
Strobe frequency 60 flashes/minute
Colour Red RAL3001
Size ( h x ) 80 x 92 mm
Weight 180 g
Ordering Information
SK20 Alarm sounder with beacon
32 different tones
Includes flashing beacon
Low profile
Very low consumption
Up to 112 dBA sound output levels
IP445 protection level
Sound output power selection
Input and output terminals provided
Easy installation
Low maintenance
Back and side cable entry
Modern and elegant design
Alarm sounder with beacon SK20
8/10/2019 Catalog Accesorii Incendiu
72/105
Page 71
Fire Sounders & Beacons
The SK40 alarm siren with luminous indicator has been designed specificallyfor external use. Its main function is to warn people outside a building of the
detection of a fire alarm inside the building. The SK40 combines the acoustic
and indicator parts in a single housing, and is activated with a single voltage
input.
Technical Data
Electrical Specifications
Supply Voltage 22 to 28 VDC
Alarm Current @ 24V 220 mA
Environmental Specifications
Ingress Protection IP33
Operating Temperature -20 to 60 C
Storage Temperature -20 to 60 CPhysical Characteristics
Dimentions (h x w x d) 297 x 210 x 75 mm
Sound Output 105 dB at 1 m
Sound Frequency 2.8 to 3.1 kHz 3%
Cycle Time 1 min ON 1 min OFF
Flash Rate 1 flash /s
Ordering Information
SK40 Alarm sounder with indicator
High sound output
Exterior operation
Sectable activation times
Optional battery backup
Optional line supervision
Alarm sounder with indicator SK40
8/10/2019 Catalog Accesorii Incendiu
73/105
Page 72
Fire Sounders & Beacons
The PA40 Xenon Strobe has been designed for in and outdoor use. It isavailable with various colour lenses to suit the application.
Technical Data
Electrical Characteristics
Supply Voltage 12/24 VDC
Current Consumption (12 VDC) 115 mA 20 %
Current Consumption (12 VDC) 35 mA 25 %
Environmental Specifications
Operating Temperature -20 C to +60 C
Operational Specifications
Flash rate 60-100 flashes/min @ 20C
Operating life 200 hours
Colours Amber, blue, clear, red
Dimentions ( h x ) 79 x 90 mm
Ordering Information
PA40 Xenon strobe light High intensity xenon
12 and 14 VDC operation
Low current consumption
Low maintenance
Xenon strobe light PA40
The CK406 electronic fire alarm bell is designed as an acoustic fire
annunciator. Thanks to their small dimensions and overall design, they are
ideal to install in-doors. The CK406 works with 24 VDC supply and the
advantage of having very low current consumption (less than 30 mA). This
makes them compatible with all good fire alarm systems on the market.
Technical Data
Electrical Characteristics
Supply Voltage 24 VDC
Current Consumption 30 mA
Physical Characteristics
Sound Output 95 dB/mColour Red
Weight 0.9 kg
Diameter 6 (150 mm)
Ordering Information
CK406 Fire alarm bell
Low current consumption
Suitable for indoor use
Easy Installation
24 VDC powered Very reliable
Low maintenance
Fire alarm bell CK406
8/10/2019 Catalog Accesorii Incendiu
74/105
ELECTROMAGNETIC DOOR HOLDERS
8/10/2019 Catalog Accesorii Incendiu
75/105
Page 74
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 42
Dimensions (mm) 70 x 85 x 40
Keeper plate flat/swivel S
Release button -
Protection diode -
Reverse polarity -
Cable entry 2EN1155 Yes
NF61937 -
BS5839pt3 -
Ordering Information
FE831 Door holder, steel box, surface mount, basic Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, steel box, surface mount, basic FE831
8/10/2019 Catalog Accesorii Incendiu
76/105
Page 75
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 42
Dimensions (mm) 70 x 85 x 40
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity -
Cable entry 2EN1155 Yes
NF61937 Yes
BS5839pt3 Yes
Ordering Information
FE832 Door holder, steel box, surface mount complete Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, steel box, surface mount complete FE832
8/10/2019 Catalog Accesorii Incendiu
77/105
Page 76
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 30
Dimensions (mm) 55 x 55 x 24
Keeper plate flat/swivel F
Release button -
Protection diode -
Reverse polarity -
Cable entry -EN1155 Yes
NF61937 -
BS5839pt3 -
Ordering Information
FE835 Door holder, steel square base Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, steel square base FE835
8/10/2019 Catalog Accesorii Incendiu
78/105
Page 77
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 70
IP rating 30
Dimensions (mm) 55 x 55 x 24
Keeper plate flat/swivel F
Release button -
Protection diode Yes
Reverse polarity Yes
Cable entry 1EN1155 Yes
VDS Coil Yes
Ordering Information
FE835VDS Door holder, steel square base, VDS magnet
Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, steel square base, VDS magnet FE835VDS
8/10/2019 Catalog Accesorii Incendiu
79/105
Page 78
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 42
Dimensions (mm) 83 x 83 x 35
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity Yes
Cable entry -EN1155 Yes
NF61937 Yes
BS5839pt3 Yes
Ordering Information
FE836 Door holder, flush mounting Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, flush mounting FE836
8/10/2019 Catalog Accesorii Incendiu
80/105
Page 79
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 42
Dimensions (mm) 83 x 83 x 46
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity Yes
Cable entry 2EN1155 Yes
NF61937 Yes
BS5839pt3 Yes
Ordering Information
FE841 Door holder, reinforced aluminium box Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, reinforced aluminium box FE841
8/10/2019 Catalog Accesorii Incendiu
81/105
Page 80
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 70
IP rating 52
Dimensions (mm) 83 x 83 x 46
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity Yes
Cable entry 1EN1155 Yes
VDS Coil Yes
Ordering Information
FE841VDS Door holder, reinforced plastic box, VDS magnet
Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, reinforced plastic box, VDS magnet FE841VDS
8/10/2019 Catalog Accesorii Incendiu
82/105
Page 81
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 40
IP rating 42
Dimensions (mm) 80 x 80 x 56
Keeper plate flat/swivel F
Release button Yes
Protection diode Yes
Reverse polarity -
Cable entry -
EN1155 Yes
NF61937 Yes
BS5839pt3 Yes
Ordering Information
FE845 Door ho lde r, wa ll mount, rein forced a luminium box Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, wall mount, reinforced aluminium box FE845
Technical Data
Dimensions (mm) 80 x 80 x 43
Ordering Information
FE845-40 Reinforced aluminium extension for FE845, 40mm
Reinforced aluminium extension for FE845, 40mm FE845-40
8/10/2019 Catalog Accesorii Incendiu
83/105
Page 82
Electromagnetic door holders
Technical Data
Dimensions (mm) 115 x 115 x 150
Ordering Information
FE845-150 Reinforced aluminium extension for FE845, 150mm
Reinforced aluminium extension for FE845, 150mm FE845-150
Technical Data
Dimensions (mm) 115 x 115 x 250
Ordering Information
FE845-250 Reinforced aluminium extension for FE845, 250mm
Reinforced aluminium extension for FE845, 250mm FE845-250
8/10/2019 Catalog Accesorii Incendiu
84/105
Page 83
Electromagnetic door holders
Technical Data
Volt 24
Power 3
Holding force (daN) 40
IP rating 42
Dimensions (mm) 128 x 110 x 80
Keeper plate flat/swivel F
Release button Yes
Protection diode Yes
Reverse polarity -
Cable entry -EN1155 Yes
NF61937 Yes
BS5839pt3 Yes
Ordering Information
FE848 Door ho lde r, fl oor mounting, re in forced aluminium box
Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, floor mounting, reinforced aluminium box FE848
8/10/2019 Catalog Accesorii Incendiu
85/105
Page 84
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 70
IP rating 42
Dimensions (mm) -
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity Yes
Cable entry -
EN1155 Yes
VDS Coil Yes
Ordering Information
FE851VDS Door holder, universal adjustable tube, 175mm, VDS magnet
Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, universal adjustable tube, 175mm, VDS magnet FE851VDS
Technical Data
Volt 24
Power 1.6
Holding force (daN) 70
IP rating 42
Dimensions (mm) -
Keeper plate flat/swivel S
Release button Yes
Protection diode Yes
Reverse polarity Yes
Cable entry -
EN1155 Yes
VDS Coil Yes
Ordering Information
FE852VDS Door holder, universal adjustable tube, 475mm, VDS magnet
Complete range for wall and surface mount
Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and French approvals (see specification)
Door holder, universal adjustable tube, 475mm, VDS magnet FE852VDS
8/10/2019 Catalog Accesorii Incendiu
86/105
Page 85
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 70
IP rating 65
Dimensions (mm) -
Keeper plate flat/swivel F
Release button -
Protection diode Yes
Reverse polarity Yes
Cable entry 1
EN1155 Yes
VDS Coil Yes
Ordering Information
FE855VDS Door holder, steel square base, IP65, VDS magnet
Complete range for wall and surface mount Low power - 1,6 W
40 daN holding power standard series
70 daN holding power on VDS coils
100% duty cycle
Anti-remnant ejector
Protection diode and reverse polarity protection on mostmodels
Release button on most models
EN and Fr
Door holder, steel square base, IP65, VDS magnet FE855VDS
8/10/2019 Catalog Accesorii Incendiu
87/105
Page 86
Electromagnetic door holders
Technical Data
Volt 24
Power 1.6
Holding force (daN) 50
IP rating Ex
EN1155 ATEX
Ordering Information
FE858EX Door holder, explosion proof
Complete range for wall and surface mount
Low power - 1,6 W
50 daN holding power
100% duty cycle
Anti-remnant ejector
EX version
Explosion proof, ATEX approval
Door holder, explosion proof FE858EX
8/10/2019 Catalog Accesorii Incendiu
88/105
TEST AND SERVICE EQUIPMENT
8/10/2019 Catalog Accesorii Incendiu
89/105
Page 88
Test and Service Equipment
Ordering Information
FG010 Universal detector removal too l on a swing f rame
ET010 Fibreglass telescopic pole 1.26 m - 4.5 m
ET011 F ib reg lass ex tension tube 1 .2 m (maximum 3 per ET010)
Universal removal tool on swing frame
- size adjustable to fit most detectors
- quick & easy removal of detectors Lightweight telescopic poles
- fibreglass
- non conductive
- use with tools up to 9m
Canvas carry bag
- easy transport of the equipment
Universal detector removal tool on a swing frame FG010
8/10/2019 Catalog Accesorii Incendiu
90/105
Page 89
Test and Service Equipment
Ordering Information
TR010 Touch sensitive transparent dispenser cup on swing frame
ET010 Fibreglass telescopic pole 1.26 m - 4.5 m
ET011 F ib reg lass ex tension tube 1 .2 m (maximum 3 per ET010)
SC008 Test Spray for Smoke Detectors
Smoke aerosol dispenser
- universal, touch sensitive
Lightweight telescopic poles
- fibreglass
- non conductive
- use with tools up to 9m
Ozone friendly test aerosol
- tests ionisation and optical sensors
- faster response and clearing times
Canvas carry bag
- easy transport of the equipment
Touch sensitive transparent dispenser cup on swing frame TR010
8/10/2019 Catalog Accesorii Incendiu
91/105
Page 90
Test and Service Equipment
Ordering Information
TH010 Mains operated heat detector test tool on swing frame
ET010 Fibreglass telescopic pole 1.26 m - 4.5 m
ET011 F ib reg lass ex tension tube 1 .2 m (maximum 3 per ET010)
Heat detector tester
- 230V mains version
Lightweight telescopic poles
- fibreglass
- non conductive
- use with tools up to 9m
Canvas carry bag
- easy transport of the equipment
Mains operated heat detector test tool on swing frame TH010
8/10/2019 Catalog Accesorii Incendiu
92/105
Page 91
Test and Service Equipment
This state-of-the-art heat detector utilises cross-flow technology for fast,efficient heat detector testing. The battery pack is contained within the test
pole
Ordering Information
TH012 Cordless, bat ter y operated , heat de tec tor on swing frame
CB001 Canvas carry ing bag for the test and service equ ipment
Heat detector testers
- battery operated
Lightweight telescopic poles
- fibreglass
- non conductive
- use with tools up to 9m
- faster response and clearing times
Canvas carry bag
- easy transport of the equipment
Cordless, battery operated, heat detector on swing frame TH012
8/10/2019 Catalog Accesorii Incendiu
93/105
Page 92
Test and Service Equipment
Ordering Information
ET010 Fibreglass telescopic pole 1.26 m - 4.5 m
ET011 F ib reg lass ex tension tube 1 .2 m (maximum 3 per ET010)
Lightweight telescopic poles
- fibreglass
- non conductive
- use with tools up to 9m
Canvas carry bag
- easy transport of the equipment
Fibreglass telescopic pole 1.26 m - 4.5 m ET010
Technical Data
According to material safety data sheet
Ordering Information
SC008 Test Spray for Smoke Detectors
No damage to detector plastics and components
Faster response tim